Search found 18 matches

by bperegrine
Wed Jan 04, 2012 9:44 am
Forum: Pullers
Topic: Columbus Winter Nationals
Replies: 5
Views: 8144

Re: Columbus Winter Nationals

http://www.ohioexpocenter.com/index.php ... Itemid=131

Ohio Expo Center
717 E. 17th Ave.
Columbus, OH 43211
by bperegrine
Wed Nov 23, 2011 10:17 am
Forum: Pullers
Topic: Rear End/ Carriers
Replies: 11
Views: 13962

Re: Rear End/ Carriers

Dodge 7.25 rear carrier and axles. Axles will need to be machined and cut down and end plates welded and axle housings will need to be bored for larger needle bearing. Usually 1 1/8".
by bperegrine
Tue Nov 01, 2011 9:46 am
Forum: Pullers
Topic: getting n to pulling
Replies: 4
Views: 7381

Re: getting n to pulling

First of all you have a great model Cub to start with in my opinion and your off to a good start. Like Farmallgray says check with the club you are going to pull with and get back to us and we can direct you better. Building a pulling tractor can be very involved depending on the class of tractor it...
by bperegrine
Fri Jun 24, 2011 4:48 pm
Forum: Pullers
Topic: Anyone running E-85?
Replies: 6
Views: 10535

Re: Anyone running E-85?

I have run E-85 in the past in my hot stock pulling tractor. It was a open RPM K341 with a mild cam and mild porting and shaved head. Nothin to fancy or modified. I followed Brian Miller's web site inscructions and drilled my jet out, cant remember the size. It was a #30 carb with top adjuster. I ra...
by bperegrine
Thu Jun 16, 2011 12:46 pm
Forum: Cub Cadets and Shooting the Breeze
Topic: 1650 motor not running right
Replies: 7
Views: 5354

Re: 1650 motor not running right

A condenser will make an engine buck, spit and kick if is bad. Wont let it wind up but will usually start and idle fine.
by bperegrine
Tue May 17, 2011 7:42 am
Forum: Pullers
Topic: My new pulling project
Replies: 18
Views: 25437

Re: My new pulling project

Here is a pic of my megaphone on my Missouri Super Stock.
by bperegrine
Mon May 16, 2011 4:58 pm
Forum: Pullers
Topic: My new pulling project
Replies: 18
Views: 25437

Re: My new pulling project

I noticed the pipe right away. I have been running a megaphone pipe for a while now.
by bperegrine
Mon May 16, 2011 1:09 pm
Forum: Pullers
Topic: My new pulling project
Replies: 18
Views: 25437

Re: My new pulling project

I like your exhaust pipe!
by bperegrine
Sun Apr 17, 2011 9:41 am
Forum: Cub Cadets and Shooting the Breeze
Topic: Hard starting 682
Replies: 13
Views: 8312

Re: Hard starting 682

I had a 682 that was hard to start last season. I did everything from overhaul the carb, plugs points etc. I ended up replacing the coil and wires and it was curred. The coil and wires on mine were one item like the wires were not meant to be removed. Anyway after it was replaced it started like a n...
by bperegrine
Fri Feb 11, 2011 11:26 am
Forum: Pullers
Topic: My Pullers
Replies: 5
Views: 9706

Re: My Pullers

My Missouri Super Stock (The WoodChipper)getting ready for its anual teardown and upgrades. Des Moines Shoot Out in March 25th & 26th next stop.
by bperegrine
Sun Jan 23, 2011 7:23 pm
Forum: Pullers
Topic: My Pullers
Replies: 5
Views: 9706

Re: My Pullers

Both tractors have VM08'S in the pictures. Have VM09's also for loose tracks. I like them both very well for the price.
by bperegrine
Mon Oct 11, 2010 5:36 pm
Forum: Cub Cadets and Shooting the Breeze
Topic: NF pto removel
Replies: 12
Views: 9900

Re: NF pto removel

should be 3 more set screws under the first ones you took out. The lower ones are pointed and grap the edge of the outter bearing to hold the clutch on. the outter set screws act like locks.
by bperegrine
Mon Oct 11, 2010 5:19 pm
Forum: Cub Cadets and Shooting the Breeze
Topic: Cub Cadet Original Enclosure ?
Replies: 1
Views: 2656

Re: Cub Cadet Original Enclosure

Here are some pics of the O
by bperegrine
Mon Oct 11, 2010 4:37 pm
Forum: Cub Cadets and Shooting the Breeze
Topic: Cub Cadet Original Enclosure ?
Replies: 1
Views: 2656

Cub Cadet Original Enclosure ?

Does anyone have any info or pic's of any type of soft cab enclosures on what might have been on an Original? I have a friend who picked one awhile back and it has what looks like rements of what used to be a cab enclosure on it such as snaps on the fenders, different footrests and metal work betwee...
by bperegrine
Wed Sep 22, 2010 2:09 pm
Forum: Cub Cadets and Shooting the Breeze
Topic: Need NF Hydraulic Lift Installation Manual
Replies: 6
Views: 5737

Re: Need NF Hydraulic Lift Installation Manual

I have a PDF copy in my PC. Cant's get it to attach in a post though. I can email it to you if I had it.
by bperegrine
Thu Sep 09, 2010 9:06 am
Forum: Pullers
Topic: My Pullers
Replies: 5
Views: 9706

Re: My Pullers

Wildcat, Open RPM K341 Stocker.
by bperegrine
Thu Sep 09, 2010 9:00 am
Forum: Pullers
Topic: My Pullers
Replies: 5
Views: 9706

My Pullers

Here are some pic's of my pullers I am currently running. My mini Farmall 560 (The Woodchipper) is a Missouri Super Stock (.060 over 16hp) and my Wildcat is a NWMGTPA single cylnder open RPM stocker. A 50 cube is in the works but may be another year to get it completed. Here is my you tube channel v...
by bperegrine
Wed Sep 08, 2010 10:07 am
Forum: Welcome Mat
Topic: Hello from MO.
Replies: 5
Views: 4946

Re: Hello from MO.

Make that 3 from Missouri!