http://www.ohioexpocenter.com/index.php ... Itemid=131
Ohio Expo Center
717 E. 17th Ave.
Columbus, OH 43211
Search found 18 matches
- Wed Jan 04, 2012 9:44 am
- Forum: Pullers
- Topic: Columbus Winter Nationals
- Replies: 5
- Views: 8424
- Wed Nov 23, 2011 10:17 am
- Forum: Pullers
- Topic: Rear End/ Carriers
- Replies: 11
- Views: 14315
Re: Rear End/ Carriers
Dodge 7.25 rear carrier and axles. Axles will need to be machined and cut down and end plates welded and axle housings will need to be bored for larger needle bearing. Usually 1 1/8".
- Tue Nov 01, 2011 9:46 am
- Forum: Pullers
- Topic: getting n to pulling
- Replies: 4
- Views: 7633
Re: getting n to pulling
First of all you have a great model Cub to start with in my opinion and your off to a good start. Like Farmallgray says check with the club you are going to pull with and get back to us and we can direct you better. Building a pulling tractor can be very involved depending on the class of tractor it...
- Fri Jun 24, 2011 4:48 pm
- Forum: Pullers
- Topic: Anyone running E-85?
- Replies: 6
- Views: 10831
Re: Anyone running E-85?
I have run E-85 in the past in my hot stock pulling tractor. It was a open RPM K341 with a mild cam and mild porting and shaved head. Nothin to fancy or modified. I followed Brian Miller's web site inscructions and drilled my jet out, cant remember the size. It was a #30 carb with top adjuster. I ra...
- Thu Jun 16, 2011 12:46 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 1650 motor not running right
- Replies: 7
- Views: 5400
Re: 1650 motor not running right
A condenser will make an engine buck, spit and kick if is bad. Wont let it wind up but will usually start and idle fine.
- Tue May 17, 2011 7:42 am
- Forum: Pullers
- Topic: My new pulling project
- Replies: 18
- Views: 25902
Re: My new pulling project
Here is a pic of my megaphone on my Missouri Super Stock.
- Mon May 16, 2011 4:58 pm
- Forum: Pullers
- Topic: My new pulling project
- Replies: 18
- Views: 25902
Re: My new pulling project
I noticed the pipe right away. I have been running a megaphone pipe for a while now.
- Mon May 16, 2011 1:09 pm
- Forum: Pullers
- Topic: My new pulling project
- Replies: 18
- Views: 25902
Re: My new pulling project
I like your exhaust pipe!
- Sun Apr 17, 2011 9:41 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Hard starting 682
- Replies: 13
- Views: 8350
Re: Hard starting 682
I had a 682 that was hard to start last season. I did everything from overhaul the carb, plugs points etc. I ended up replacing the coil and wires and it was curred. The coil and wires on mine were one item like the wires were not meant to be removed. Anyway after it was replaced it started like a n...
- Fri Feb 11, 2011 11:26 am
- Forum: Pullers
- Topic: My Pullers
- Replies: 5
- Views: 9991
Re: My Pullers
My Missouri Super Stock (The WoodChipper)getting ready for its anual teardown and upgrades. Des Moines Shoot Out in March 25th & 26th next stop.
- Sun Jan 23, 2011 7:23 pm
- Forum: Pullers
- Topic: My Pullers
- Replies: 5
- Views: 9991
Re: My Pullers
Both tractors have VM08'S in the pictures. Have VM09's also for loose tracks. I like them both very well for the price.
- Mon Oct 11, 2010 5:36 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: NF pto removel
- Replies: 12
- Views: 9960
Re: NF pto removel
should be 3 more set screws under the first ones you took out. The lower ones are pointed and grap the edge of the outter bearing to hold the clutch on. the outter set screws act like locks.
- Mon Oct 11, 2010 5:19 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Cub Cadet Original Enclosure ?
- Replies: 1
- Views: 2680
Re: Cub Cadet Original Enclosure
Here are some pics of the O
- Mon Oct 11, 2010 4:37 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Cub Cadet Original Enclosure ?
- Replies: 1
- Views: 2680
Cub Cadet Original Enclosure ?
Does anyone have any info or pic's of any type of soft cab enclosures on what might have been on an Original? I have a friend who picked one awhile back and it has what looks like rements of what used to be a cab enclosure on it such as snaps on the fenders, different footrests and metal work betwee...
- Wed Sep 22, 2010 2:09 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Need NF Hydraulic Lift Installation Manual
- Replies: 6
- Views: 5769
Re: Need NF Hydraulic Lift Installation Manual
I have a PDF copy in my PC. Cant's get it to attach in a post though. I can email it to you if I had it.
- Thu Sep 09, 2010 9:06 am
- Forum: Pullers
- Topic: My Pullers
- Replies: 5
- Views: 9991
Re: My Pullers
Wildcat, Open RPM K341 Stocker.
- Thu Sep 09, 2010 9:00 am
- Forum: Pullers
- Topic: My Pullers
- Replies: 5
- Views: 9991
My Pullers
Here are some pic's of my pullers I am currently running. My mini Farmall 560 (The Woodchipper) is a Missouri Super Stock (.060 over 16hp) and my Wildcat is a NWMGTPA single cylnder open RPM stocker. A 50 cube is in the works but may be another year to get it completed. Here is my you tube channel v...
- Wed Sep 08, 2010 10:07 am
- Forum: Welcome Mat
- Topic: Hello from MO.
- Replies: 5
- Views: 4974
Re: Hello from MO.
Make that 3 from Missouri!