Search found 13 matches
- Fri Feb 21, 2014 11:31 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Inline heaters for diesels
- Replies: 7
- Views: 6189
Re: Inline heaters for diesels
I got my frost plug heater ( 400 watt) for D600 head at Kubota dealer a year ago, I think for $40 or less. It fits nicely behind fan bracket . Just taking time to pull grill, radiator,air cleaner assy. & brackets ,etc., but wasn't too bad over a couple sun shining afternoons with the shop overhead d...
- Wed Feb 19, 2014 10:05 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Inline heaters for diesels
- Replies: 7
- Views: 6189
Re: Inline heaters for diesels
With a couple days of 40*, time to install engine heater kit ( Kubota ) # 70000 73595 , it goes in head/ frost plug( D600 ) behind fan bracket assembly. Pulled radiator & grill to give easy access. May replace lower radiator hose (OEM $$) since I did upper hose couple years ago. Today must cutout ho...
- Fri Dec 23, 2011 8:05 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 59m shredder
- Replies: 20
- Views: 19700
Re: 59m shredder
If you want smaller sized material, I just run shredded material thru again & again! >>> PWR
- Tue Dec 20, 2011 12:16 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 59m shredder
- Replies: 20
- Views: 19700
Re: 59m shredder
That screen looks to be an after market or shop made one. When I bought my 59M in '70s I also purchased a bar screen along with the ( I think ) std. 1" screen. Wet/ green material will plug 1" screen in short order. I used bar screen most times or without one. Works good on material up to 1". Cub Ca...
- Thu Dec 01, 2011 1:27 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Thank you Santa !!
- Replies: 7
- Views: 5147
Re: Thank you Santa !!
Looks Good !!
- Mon Sep 19, 2011 9:25 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Diesel coolant hoses
- Replies: 22
- Views: 13320
Re: Diesel coolant hoses
Vince, when I replaced my Diesel's top hose, a few years ago, I wrapped it with pipe insulation (12" length of formed foam type) & used foil vent duct tape to hold in place. PWR ...... Oh yeah, I must have bought the last ones in country, they were pretty pricey$$$.
- Thu Aug 25, 2011 2:29 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1512 Diesel Problems!
- Replies: 8
- Views: 6943
Re: 1512 Diesel Problems!
Time to pull Fuel tank, clean & flush, maybe fuel lines, filters,tank shutoffs/screens. You'd be surprised all the crud that can accumulate in there.
- Thu Aug 25, 2011 1:58 pm
- Forum: The Coffee Shop
- Topic: Well its offical
- Replies: 20
- Views: 12944
Re: Well its offical
Vince , that sounds Great! I wish you the best... PWR
- Thu Jun 09, 2011 10:41 am
- Forum: The Coffee Shop
- Topic: critique my hold downs on my trailer & new ramps built
- Replies: 9
- Views: 6771
Re: critique my hold downs on my trailer & new ramps built
Ditto to what Frank posted! I drilled hole in each ramp & used .25" diameter bolt to hold in place on previously owned Kory 2 wheel trailer. I don't trust straps, just old school I guess.
- Mon Jan 24, 2011 6:46 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1782 Broken implement lift arm
- Replies: 43
- Views: 36225
Re: 1782 Broken implement lift arm
# 603-0027 lift bracket is backordered @ MTD/CCC until March according to CC parts dept. My local CIH dealer was backordered for 2 since before Christmas. Just My 2 cents. Good luck finding 1 on someones shelf...
- Tue Jan 11, 2011 4:03 pm
- Forum: The Coffee Shop
- Topic: wider snow blade
- Replies: 9
- Views: 7137
Re: wider snow blade
When I bought my 1450 with 2 valve hyd, I traded for a 54" blade & Hyd. angle... Excellent snow mover , only improvement would be foot pedal Hydro. Use plenty weight ...
- Tue Nov 23, 2010 11:56 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 122 w/creeper gear & mulching leaves
- Replies: 11
- Views: 8615
Re: 122 w/creeper gear & mulching leaves
Got back from Cabo Sunday nite, So Monday after noon, it was wet, but my Easy Vac & # 4 IH cart with my 882 w/50C did last run for leaves. This fall was first time with Gator Blades -- they worked great to help pulverize grass & leaves. Probably won't need to use Troy-Bilt chipper shredder to make c...
- Wed Sep 08, 2010 9:56 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 682 loader
- Replies: 10
- Views: 9331
Re: 682 loader
Matt Great job!! I just missed a loader like yours (not refurbished)about 40 miles north of Mad City. Darn, I didn't check my Email soon enough in morning. PWR