Search found 25 matches
- Sun Mar 29, 2015 1:51 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Tiller ID
- Replies: 5
- Views: 4495
Re: Tiller ID
that is a #1 tiller and the correct mule drive belt should be 549250R1 and yes just use the mule drive carriage you have
- Fri May 23, 2014 4:43 pm
- Forum: Farmall and Farmall Cub
- Topic: 44 h cast broke
- Replies: 3
- Views: 5459
Re: 44 h cast broke
only 2 ways to repair cast iron that will last best way is to have it welded with a powder torch or grind the cracks out good and braise them with brass if you could find a used steering bolster in good shape that would be the best bet as for the wheels shimming in 5th gear the teeth are worn on the...
- Thu Apr 17, 2014 6:31 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 782 & TLLER QUESTION...
- Replies: 10
- Views: 6349
Re: 782 & TLLER QUESTION...
i have a 2b tiller on my 782 the belt numbers cub cadet 135553c1 caseih 492923r2 gates b151 i have been using the gates b151 for years its less than half the price of the belt from cub cadet or caseih
- Mon Feb 10, 2014 5:31 pm
- Forum: Farmall and Farmall Cub
- Topic: 6 to 12
- Replies: 3
- Views: 6082
Re: 6 to 12
there is a few ways to go about this you can use a 12 volt generator like on a d17 allis chalmers it bolts right in place farmall adjustable pulley and all change the light bulbs to 12 volts and add resisitor to coil or install resistor type coil if its a magneto then your good or like others have s...
- Mon Jul 22, 2013 5:31 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: diesel valve adjustment
- Replies: 2
- Views: 2580
Re: diesel valve adjustment
its a very simple job just pull rocker cover off roll each cylinder to top dead center and adjust the gap between the rocker arm and valve stem to .007 with a feeler gauge just tight enough to barely drag the feeler guage the rocker arm has a jam nut and a slotted bolt to adjust it
- Mon Jul 22, 2013 5:26 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: Which Manual has it??
- Replies: 2
- Views: 2715
Re: Which Manual has it??
the 1320 is almost the same mower except the m14 engine
- Sun Jul 21, 2013 2:05 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: spark plugs for the M14 engine
- Replies: 2
- Views: 2713
Re: spark plugs for the M14 engine
the factory plug is a champion RH10C the ngk plug is a 3212
- Wed Mar 20, 2013 4:22 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
kit came from repower specialist in Oregon good people to work with it was 2095.00 delievered no problems at all smoothest running engine I ever owned has tons of power and burns hardly any gas
- Fri Nov 23, 2012 8:45 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 1650 Air Filter
- Replies: 2
- Views: 2616
Re: 1650 Air Filter
yes wix made filter is a 2296 or their small engine line is a 702235
- Tue Nov 06, 2012 11:51 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Need Tiller Information
- Replies: 1
- Views: 2196
Re: Need Tiller Information
the pulley diameter is 5in the belt is 7/16 x 145in
- Thu Oct 18, 2012 6:32 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
- Thu Oct 18, 2012 6:31 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
- Thu Oct 18, 2012 6:28 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
- Thu Oct 18, 2012 6:27 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
- Thu Oct 18, 2012 6:25 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
got my cub all finished up the honda runs great
- Thu Oct 18, 2012 6:20 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: cub cadet 1000
- Replies: 3
- Views: 2834
Re: cub cadet 1000
thanks guys i havent owned anything but hydros
- Wed Oct 17, 2012 9:24 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: cub cadet 1000
- Replies: 3
- Views: 2834
cub cadet 1000
are the cub 1000 mowers any good i found a real slick one for 100.00 running with deck he also has a slick 108 with deck for same price
- Sat Oct 13, 2012 8:37 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
vince there is a solid white and a black with yellow stripe coming out of the regulator harness and the 3 wire engine harness has a red-white-black wires in the plug i put the 2 gray wires from the stator to the 2 grays and put the black wire with the eyelet to ground i can get some pictures if need...
- Fri Oct 12, 2012 11:01 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
i need alittle help with the wiring on this honda i have 2 wires left from the voltage regulator i dont know where to put them and what to do with the 2 wire factory harness plug i took the solonoid out beside the battery and ran a new positive cable to the starter post and a wire from the key switc...
- Sun Oct 07, 2012 9:55 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Blocks
- Replies: 9
- Views: 5805
Re: Blocks
sleeving the k321 to a k241 should be no problem only a 1/4 in difference the blocks are the same except bore size the valves in the 241-341 are the same size the 241 has a shorter stroke and the 301-321-341 have the same stroke
- Wed Oct 03, 2012 9:51 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Kohler 12hp problems
- Replies: 11
- Views: 6989
Re: Kohler 12hp problems
where is it breaking the rod at ?
- Sun Sep 30, 2012 8:51 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
well guys after looking at the new gx hondas its without a doubt my choice they have forged steel cranks forged steel rods with inserts bearings on both ends of the crankshaft 1 piece cast iron cylinders with no head gaskets very well built i do thank all of you for the posts and pictures i just did...
- Sun Sep 30, 2012 3:12 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
thanks for posting that it looked good it looks like honda is winning this one anybody running commands in these
- Sun Sep 30, 2012 2:03 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
Re: repowering a 782
thanks for the reply i have read your install before honda has changed the engine design its alittle different from your 610 but somewhat the same i have no experience on v-twin hondas only the single cylinder ones i have some experience with commands its a hard choice between the two
- Sun Sep 30, 2012 1:21 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: repowering a 782
- Replies: 21
- Views: 28721
repowering a 782
i am debating on which would be the better engine to replace the kt-17 honda gx 630 or kohler command 23 both drop in kits are the same price what are the pros and cons of both engines i use it for tilling and plowing not alot of mowing any advice would be helpful thanks