Search found 25 matches
- Wed Apr 20, 2016 1:39 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Tire Size
- Replies: 1
- Views: 2189
Re: Tire Size
23×10.5×12 tire on the cyclops, non super garden, tractors use that size and offset. The supers use a 12x8.5 wheel with 26x12x12 tires but have a different offset.
- Fri Mar 25, 2016 1:47 am
- Forum: CCC and MTD Built Cub cadets
- Topic: 1572 rear end
- Replies: 66
- Views: 46822
Re: 1572 rear end
I had both sides welded up on my 2182 a couple of years ago by a guy at work using a tig and they came out looking very nice and are still looking good. I did have him add some extra bracing at the time also. I use this primarily with a blade now and don't baby it.
- Sat Feb 06, 2016 10:43 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Brinly Cat 0 Plow
- Replies: 2
- Views: 3459
Re: Brinly Cat 0 Plow
Here is the manual for a 12 in. brinly.
- Wed Jan 13, 2016 10:45 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1772 updates
- Replies: 27
- Views: 23826
Re: 1772 updates
Nice blade and plow. Do you have the mounting plates on the tractor?
- Fri Dec 11, 2015 9:46 am
- Forum: CCC and MTD Built Cub cadets
- Topic: NUsed Adapter Housing and Support Brackets
- Replies: 32
- Views: 36919
Re: NUsed Adapter Housing and Support Brackets
Really nice looking finished product. Hope you get plenty of snow to push around. Cub Cadet recommends taking two of the springs off for pushing snow so the blade trips easier in case you hit something that doesn't move. Good looking original also.
- Fri Oct 02, 2015 10:22 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Cub Cadet 1440
- Replies: 5
- Views: 5457
Re: Cub Cadet 1440
According to parts tree the model 318, 44 inch and model 320, 42 inch are for the 1440 tractor but it seems that the model 321 46 inch, the model 317 48 inch, and the model 324 54 inch decks should also fit unless it's a horsepower issue. I'm not familiar with QL models so can't help with those.
- Thu Sep 24, 2015 9:20 am
- Forum: The Coffee Shop
- Topic: Ag tire question
- Replies: 6
- Views: 6619
Re: Ag tire question
You can run chains with your ags and the traction is better than without chains but turfs with chains will give the best traction in my experience with my supers. The chains on my firestones that came with my 2182 don't fall between the treads too bad if you keep them tight. The rear wheel size is 1...
- Sat Sep 12, 2015 1:52 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: NUsed Adapter Housing and Support Brackets
- Replies: 32
- Views: 36919
Re: NUsed Adapter Housing and Support Brackets
I have four of these setting around and on my supers and they are all the same size, with the exception of the one I had made by a friend at work to replace one that I broke. Here is a drawing of mine. I have changed some sizes due to making it heavier duty or (harder to break).
- Wed Aug 19, 2015 9:26 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1811 snowblower
- Replies: 9
- Views: 8863
Re: 1811 snowblower
According to Parts Tree, it looks like a model 450, 45" two stage snow blower is what should fit your 1811.
- Wed Aug 19, 2015 7:25 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 2182 pictures please
- Replies: 15
- Views: 9562
Re: 2182 pictures please
You could have them measure the carb opening and see if any pod filters, like what is used on motorcycles, are available to use either temporarily or as a permanent solution. It's better than using it without one.
- Wed Aug 19, 2015 9:00 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 2182 pictures please
- Replies: 15
- Views: 9562
Re: 2182 pictures please
Here are a couple more pics. Notice that there were two different style brackets to hold the filter assembly. The 1782 filter assembly should work also except for the hose from the intake manifold to the filter housing. Note that the last two pics are from a 1782 D640 diesel engine. If you need any ...
- Tue Jun 30, 2015 6:40 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: NUsed Adapter Housing and Support Brackets
- Replies: 32
- Views: 36919
Re: NUsed Adapter Housing and Support Brackets
The brackets are for the rear mounts for a haban blade. I see I also left one dimension out. The spacing is 3.5 inches from the top side of the bracket to the .665 hole on the bottom right side. EDIT The drawing a few posts up have been updated.
- Sun Jun 28, 2015 5:13 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: NUsed Adapter Housing and Support Brackets
- Replies: 32
- Views: 36919
Re: NUsed Adapter Housing and Support Brackets
Here are the dimensions I copied from my 2182 haban brackets. I remade mine out of .210 stainless and they fit and work well.
- Fri Feb 27, 2015 10:17 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: Haban Blade 401 assembly
- Replies: 33
- Views: 33221
Re: Haban Blade 401 assembly
I replaced my cutting edge with a piece of 1/2 x 6 x 55 inch flat bar. It strengthens the blade and lasts much longer than the original cutting edge. Just drill round holes and put hex bolts in it. It plows the same and can still be flipped.
- Sun Jan 04, 2015 9:20 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: Cab on the 2182
- Replies: 1
- Views: 2262
Cab on the 2182
Put a cab on the cub 2182 super after having to tweak the rear brackets straight and strengthen them by welding 3/8 inch square stock to the sides.
- Fri Jan 02, 2015 4:54 pm
- Forum: Custom Corner
- Topic: My 106 Refurb/Mod
- Replies: 10
- Views: 12664
Re: My 106 Refurb/Mod
Very nice tractors you have there. What are those rear off of, the ones with the holes?
- Fri Jan 02, 2015 4:48 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
On the Cyclops tractors, at least the supers which is what I have, the arm pushes to lift the 451/551 blower or the haban snow blade. All Cyclops supers have hydraulic lift and I don't know if the manual lift Cyclops utilizes a pull to lift setup as I'm only familiar with the Cyclops SGT. Thanks.
- Wed Dec 31, 2014 8:12 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
Trust me, I only copy other ways I've seen and probably throw away 5 or 6 attempts before I'm happy with the results and I can understand it. The tv comment is just a saying I've been using for years.
- Wed Dec 31, 2014 2:34 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Kubota Starter Replacement (1772, 1782, 2182, etc.)
- Replies: 12
- Views: 12406
Re: Kubota Starter Replacement (1772, 1782, 2182, etc.)
Tom, Thanks for the write up. You do nice work. My 2182 starts and runs great but the 1782 is probably going to need a starter up grade in the near future due to slow cranking when hot. I appreciate and enjoy your detailed write ups. Keep up the good work.
- Wed Dec 31, 2014 2:23 am
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
Good deal. Glad it helped you. Any pics of finished product?
- Mon Dec 01, 2014 2:55 am
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
I decided to scratch out a better pic. Hope it helps. PS I'm no draftsman nor did I play one on TV.
- Sun Nov 30, 2014 7:03 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
Couple more size pics.
- Sun Nov 30, 2014 6:48 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
The pic should have the bolt size as 5/16 X 1.5 x18 tpi. Sorry about the mixup. I actually measured mine again and mine is made out of 1 inch flat bar and only had to grind a little bit off due to rubbing the brake pedal.
- Sun Nov 30, 2014 4:52 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
Updated pic, bolts are 5/16 dia. 18 tpi X1.5 long. Top part is 3/4, in the new pic it tapers from 5/16 down to 1/4 at the bottom. Note that bolt holes on the right are tapped and left side are just drilled through holes so that the bolt tightens onto rockshaft and not the lift bracket. I made mine 3...
- Sun Nov 30, 2014 5:24 am
- Forum: CCC and MTD Built Cub cadets
- Topic: 1440 Lift Bracket
- Replies: 15
- Views: 11581
Re: 1440 Lift Bracket
Here are dimensions from a cyclops with hydraulic lift. The width is 3/4 and the pin is 1/2 dia. but I changed my dia. to 5/8 due to breaking the smaller size multiple times.