Cub Cadet Collectors dot com

Guys I'm really missing the boat. From southern IN, we or a least I, are a little slow

Don't get the china statement

Kind of done need to sand blast the rims and weights the paint. All OEM 78' 1000. Got very lucky. The original owner took care of her.

Got a dirt blade for my 78 1000. Didn't get the rod to do the lifting with any pic on them. I will probably make it, can't be that hard.

I like it thank you. Better pic.got a dirt blade for it what is the color of it . Looks to be white not cream color of the cubs

1978 cub 1000. Got it from the original owner. Put the tires on it but other than that OEM.

Got to put the panels on. Could not wait

Thanks guys, just got done with the change over of the new parts. The oil pan is fine. Had a bolt that was hard but ran a tap in it to help. It did. There are two holes below the pulley on the front of the engine cradle, since I'm not going to use it to mow with I'm voing to bolt the rails together ...

Got all the parts I need to put a new clutch in my 78 1000. A new flex plate as well, motor mounts, teaser spring, rag joint, throw out bearing. Any pit falls I need to look for. I have the engine out of it already going to clean/ degrease the whole think before putting it together tomorrow. Just wo...

I am wrong. The toe refers to front and back. I have a " vertical lean" to the front tires. Almost like a steering pivot is bad (bolt and spacer). Don't appear to be as I took it apart and check for play.one is about a 1.25 out at the bottom when a level touches the top. The other 1 in. Whats up?

How is the way you guys set the proper angle for the front of a cub 1000? I was thinking set a level vertical, touch the top of the tire and measure the bottom to the spec. What do you all think.

Did not think it did under the spec sheet in the owners manual it did not list the 1000. I could be reading it wrong. I do that think alot, not understand or read WAY to much into it.

Looked everywhere in my manual for the lube to use on my 78 1000 cub. For the life of me I could not find it, any help, what should I use. The owner's manual just about the 1250 1450 and 1650 to use IH hydran fuild. I would think so type of gear lube in the transmission. What should I use thanks

Take the fenders off to get the shifter out and the weld was broke. Any thoughts on how to compress spring for disassembly? Think I'm going to make a tool for this or get crafty with it.

Mr. Dave C. I believe you are right. I can move the shifter, when in gear, almost a full circle. The shifter is very sloppily. Do you know where I can find a exploded view of tranny and or how to fix my problem. Thanks alot you have helped. Will try to post pics if I can figure it out not very compu...

Paul I would love to attend, please email at clayhustler@yahoo.com. The more I think and after talking to a gentleman, we have come to think the "H" on the under side of the trans cover is broken. The tractor is in factory condition, never been hacked up. One reason I purchased it. I dont have a lot...

Why is it when I put my gear shift in the "1st" position it goes in 3rd. The "2nd and 3rd" position seam to be "2nd". Reverse is where it should be. Gear shifter is not that loose, I dont think that is but dont really I know.

Dad comes over. He is ready to covert his 52 farmall h to 12volts. Finally after years of begging him. I have looked around on youtube and other forums for pics and knowledge. Cant really find a good parts list to go to store with. I know whole kits are sold but wow, high dollar. There has to be som...

Thanks Knight, that makes sense. Just got to know what makes tick. Sorry could not resist.

Bout a minute. Just thinking off is off.will try the test light. The a contact off th e switch runs to the meter, thats what another forum said. Contact might be sticky.

Why is my meter running on my 1978, cub 1000 when the key is OFF and OUT of tractor. I will start it let it run then shut it off. The meter continues to run. Stops for a little then runs some more before it stops.The meter that is. Is it a bad switch, contact in switch or just my dumb luck. Help got...

Jeff those are very nice parts. What about the lift arm and hardware for the top, do you machine tbat as well? All I have seen look like cast.

Sorry guys. A plow for garden. See how new I am to it...lol

Kind of new to this so bear with me. I would like to get a plow for my 1000 but I dont know what kind of lift arm/hardwear I need. I have tryed t I look it what but have yet to find a picture of what I need. I junk alot and have know idea what to look for. Pic would be great or if anybody has one fo...

I love the .219. I am sure a few chucks have fell there in Pa. To those beautiful rifles.

I like 24hourcampfire.com, rimfirecentral.com. Hey Bryan rimfire will show you how to do a trigger job on your Ruger. Also love the .22 rimfire. If it has tbe name REMINGTON on itit will have a new home.

ERICR is hat a 03 springfield sporter? Love love the unertl scopes. I want a 2 1/2 varmint scope very hard to fine. I have a bad bad problem when I find a old scope that needs to be cleaned up and used.Bryan do you shoot ling range 200-400 yds. I have a few steel plates I shoot at just wondering if ...

I willbe there that sounds like a hellva lot of fun. Thank you very much for the info. Look foward to meeting you.

Dont know what to ask. Dont know much about the whole tire thing(new to the sport). I want a wide tire on the back and no side wall bulge. How can I do that. We dont live but 40milse apart

I have a set of 26x12x12 ag Carlisle that have 20hrs on them. I got them at a yard sale, took the gamble they would fit on my 1000(don't know what I was thinking!). A great price to. Would love to find someone to swap some tires. I have a set of 10" rims for the 1000 and need a set of 23x10.5x12 for...