Search found 143 matches
- Sun Apr 21, 2024 6:48 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Leaking Hydro
- Replies: 5
- Views: 134
Re: Leaking Hydro
the clear plastic is a cover over the glue that is to be removed before installing the gasket
- Sat Apr 02, 2022 7:47 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Brake issues
- Replies: 1
- Views: 920
Re: Brake issues
lube the pivot points, is the spring hooked to the front transmission mount bracket ?
- Sun Nov 21, 2021 10:04 am
- Forum: CCC and MTD Built Cub cadets
- Topic: LTX 1040
- Replies: 2
- Views: 1533
Re: LTX 1040
they're a decent lawn tractor and hold up pretty well ,if not over worked by pulling heavy carts and such. no good for mowing real high grass either
- Thu Jun 04, 2020 5:49 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Cub Cadet 125
- Replies: 5
- Views: 4163
Re: Cub Cadet 125
post them in the for sale section.
- Mon May 25, 2020 7:01 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Carb Repairs
- Replies: 9
- Views: 5714
Re: Carb Repairs
I've used a few now only problem was the plastic float arm was separated from the float . I used the old float and it worked great
- Sun Apr 26, 2020 8:05 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Kohler Command 22HP Engine issues
- Replies: 2
- Views: 2698
Re: Kohler Command 22HP Engine issues
by putting air pressure in the cyl. it will hold the valves closed so you can work on the keepers
- Wed Nov 27, 2019 6:45 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 1710 hydro tranny
- Replies: 1
- Views: 2176
Re: 1710 hydro tranny
just go real slow will be fine
- Sun Sep 22, 2019 7:38 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 1811 Relay
- Replies: 4
- Views: 3713
Re: 1811 Relay
runs the pto clutch
- Thu Sep 19, 2019 7:20 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 125 hydro problem
- Replies: 3
- Views: 3154
Re: 125 hydro problem
1 valve is forward .1 is reverse
- Wed Sep 18, 2019 4:47 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 125 hydro problem
- Replies: 3
- Views: 3154
Re: 125 hydro problem
button on top of release valve stuck down .
- Fri Jun 28, 2019 5:53 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: How to Disconnect Engine from Shaft ???
- Replies: 8
- Views: 5567
Re: How to Disconnect Engine from Shaft ???
yes. you'll have to lift it also because the oil pan will hit the frame
- Thu Jun 27, 2019 4:55 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: How to Disconnect Engine from Shaft ???
- Replies: 8
- Views: 5567
Re: How to Disconnect Engine from Shaft ???
the engine should slide forward and come off the shaft. the slot in the coupler usually has wear so you will probably have to rotate to line it up . ive installed a coupler from a 1450 with the rubber flex disc instead of the slotted coupler that tends to break pins and wear the pins and coupler . h...
- Thu May 30, 2019 6:41 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Got 2 rescue dogs, 1 rescue cat and now a rescue Cub Cadet
- Replies: 1
- Views: 2229
Re: Got 2 rescue dogs, 1 rescue cat and now a rescue Cub Cad
should be a 42" deck, turn the 2 outer blades end to end and measure total width . the 44 / 50 decks don't have cast iron noses
- Tue May 28, 2019 5:15 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 582 Cub Cadet
- Replies: 2
- Views: 2641
Re: 582 Cub Cadet
25 - 32 volts ac IIRC............sounds like the pto might be shorted
- Sat May 25, 2019 9:30 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Loader Mutt Continues...
- Replies: 352
- Views: 995277
Re: Loader Mutt Continues...
if the race won't be used weld around the id of it and it should shrink enough to all but fall out
- Thu Jan 17, 2019 5:35 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Uneven piston gap to Cylinder walls
- Replies: 5
- Views: 4478
Re: Uneven piston gap to Cylinder walls
the piston is worn at the top due to carbon build up at that area , if you tear it down it will probably need bored , might as well just try it the way it is and see how it runs
- Fri Sep 21, 2018 6:25 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Johnson loader fluid fill
- Replies: 2
- Views: 3615
Re: Johnson loader fluid fill
crows foot wrench ?
- Wed Aug 22, 2018 6:36 am
- Forum: CCC and MTD Built Cub cadets
- Topic: 1211 Charge Pump / Driveline Coupling
- Replies: 1
- Views: 2530
Re: 1211 Charge Pump / Driveline Coupling
I know the quiet lines have them , I looked up the parts list on yours and it doesn't show any , is the end of the shaft rounded to eliminate the need for the ball ?
- Sat Jul 07, 2018 11:47 am
- Forum: CCC and MTD Built Cub cadets
- Topic: Super Axle pivot slop and repair
- Replies: 8
- Views: 7215
Re: Super Axle pivot slop and repair
the may not be worn much in the axle it might just need the bolt tightened up some if the axle is moving front to back when steering
- Mon Jun 18, 2018 8:31 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 782 strange behavior
- Replies: 3
- Views: 3366
Re: 782 strange behavior
check the gap on the clutch set at .010 .....
- Wed May 30, 2018 6:15 am
- Forum: CCC and MTD Built Cub cadets
- Topic: 2082 hydraulic fitting leak
- Replies: 3
- Views: 3996
Re: 2082 hydraulic fitting leak
years of vibration and flexing when the tractor twists . are the rear axle mounting bolts all tight?
- Thu May 24, 2018 5:23 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 60" 190-374-100 deck 6.5" top of double pulley came off
- Replies: 5
- Views: 4810
- Thu May 24, 2018 5:22 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 129 Dies and is Hard to Start Again ???
- Replies: 7
- Views: 5228
Re: 129 Dies and is Hard to Start Again ???
yes that coil will work . it says it has the internal resistor
- Sat May 12, 2018 7:46 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: cub 128 mowing heigth adjustment
- Replies: 2
- Views: 2839
Re: cub 128 mowing heigth adjustment
you are correct
- Sun May 06, 2018 9:07 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Original clutch linkage
- Replies: 11
- Views: 7753
Re: Original clutch linkage
the brake band could be worn out or broken they're the same as the international cubs use , just take the left axle housing assy. off and look it over
- Fri May 04, 2018 7:09 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 1993 1440 won't crank
- Replies: 7
- Views: 6031
Re: 1993 1440 won't crank
the ignition switch plug causes a lot of problems try wiggling it to see if it will crank if so then a new switch and a plug is probably needed
- Thu May 03, 2018 6:21 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: need deck belt
- Replies: 2
- Views: 2756
Re: need deck belt
754 3004 1/2" x 78" ...the documents and manuals section at the top of the page has a belt application in it
- Fri Apr 13, 2018 6:18 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: Wheels for 1200
- Replies: 2
- Views: 2614
Re: Wheels for 1200
yes they were an option
- Sun Mar 25, 2018 9:09 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: kt 17 motor series I
- Replies: 2
- Views: 2402
Re: kt 17 motor series I
there should be a tag under the left side of the intake on a plate
- Thu Mar 15, 2018 9:58 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: mower deck
- Replies: 7
- Views: 6530
Re: mower deck
post a pic. of the whole deck . measure the width of the blades have the 2 outer blades turned end to end and measure the full width