Cub Cadet Collectors dot com

Thanks for the help, I will save this information so when I ready to installed the decales.
Have a great day.
Martin

Does anyone have a picture of a original cub cadet mower deck 38" with the correct placement of the decales.
Thanks,
Martin

Cleaning up behind my shop and looked at one of my original cub cadet mower deck that I bought years ago, one of them had a mulching plate with the IH bolts, cleaned it up and will be putting it on a original mower deck that I'm going to restore. I figured out how to resize my picures I will post mo...

Thank you, that is what I have . I wanted to make sure, I was looking at the two original mower deck that I bought and one had the mulch plate on it just like the picture you sent. I have the guard, but I took it off, now I going to put it back on the way you have yours in the picture. Have a great ...

Thanks for the picture, not all of the plate is in the picture, do you have a picture that shows the complete plate, and have a great day.
Martin

Does anyone have a picture of a mulch plate that was on the mower deck 38" on a Original Cub Cadet. Everyone have a great day.
Thanks,
Martin

Paul,
Thanks for the information and have a great day.
Martin

Does anyone know if the IH plant building in Louisville KY is still there? or know where I can fine some pictures of it.
Thanks,
Martin

Does anyone know if the IH plant building in Louisville KY. is still there? or know where I can fine some pictures of the old IH plant.
Thanks,
Martin

David,
I'm runing out of room to, looks like you are not to far from me. I have two Orginals 1962 and 1963. These guys are very helpfull.
Martin McKinley
Lebanon, Ohio

Thanks for the pictures.
Martin

Greezer do you have any pictures of the M&W 9 speed transmission that was used on the Original Cub Cadet, I was reading in the Red Power forum that you had one, and have a good day.
Martin

Thanks for all the information.
Haybail

Paul, I was talking about the battery box, my 1962 has the smaller one and my Dads 1963 has the larger one, just like the one that is on EBAY right now and it is a good picture of the larger box. Over the years I have seen two other originals with the larger battery boxes and they look like factory ...

Question, on the original cub cadet dash towers why are some battery holders bigger than others, I have two, one for the small battery and one that will take a full size battery, there is one on on ebay right now with the larger one. When did IH make the change. Hope everyone has a great weekend. Ha...

Geezer,
I got the seals from Scott Madson, I only had to install the front one, no leaks and the creeper gear is working fine.
Thanks for your help. Martin

Chris
Go ahead and put fenders on it, you can get a good set just for a ARM. Great job.
Martin

wdeturch,
If you fine the number for the seal it would be very help full and have a good day.
Martin

Thanks Dave.
Martin

Dave C. I read your post and you said you have rebuild a few creeper gears. I have a Danco UD-6 for my original cub cadet, could you tell me where you got the parts I will be replacing the top front seal and the "O" ring, on the parts section of the manual it is item 1 and 3 and have a good day. Mar...

I found my clearance problem, when I removed the lift arm one of the support arm brackets came off, I just stuuck it back on, I didn't know there was a difference, turn it around and I have all kind of clearance. You live and learn.
Martin

wdeturck I have my creeper gear shaft installed, one thing I see there in not much clearance between the lift arm shaft and the two machine bolts on the end of the driveshaft, did IH have a special machine bolts for this. I have turn the engine over and pushed in the clutch petal and it is not hitti...

Wdeturch, I pre. fitted everything this morning, to make sure it was right, took it back apart and pre. loaded the spring tension and set the roll pin, cleaned it off and some masking and painted it, will put it in the tractor next week. I did leave some extra on the end. Again thanks for the help a...

wdeturck, Thanks for the information, I have a spare drive shaft for the ones that do not have a creeper gear. I took it apart yesterday, going to clean it up and check the spacing of the hole. I have a Drake arbor press and made it easy to take it apart, hope you have a good day. Martin

I took a Danco UD-6 creeper gear and drive shaft out of a 1961 Original Cub Cadet and put it in a 1963 Original Cub Cadet and the Clutch pully does not line up, it is off by 1/2 to 3/4 of a inch. The drive shaft fits good in the end of the creeper gear that part is ok, any help would be appreciated....

JMotuzick
Thanks for the information.
Martin

WDETURCK,
Thanks for the information, I will give it a shot, where can you buy them, and have a good day.
Martin

On the Original Cub Cadets that had the Danco UD-6 creeper gear, the output shaft of the transmission has a 1/4" hole for the harden roll pin, but the input shaft on the creeper gear has two slots and they are 3/16". Did they make a special pin for this ?? Thanks, Martin

Thanks guys for all the help.
Martin

I can not fine nothing of the web about a Danco company that made a creeper gear, I did fine out that some of Danco items was made by the Danuser Machine Works , but not the Danco Creeper gear that is why I ask the question. Thanks, Martin