Search found 12 matches
- Sun Aug 12, 2012 9:30 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: kohler front pulley help
- Replies: 4
- Views: 3391
Re: kohler front pulley help
i did soak it earlier today numerous times before i went to work with pb blaster. im going to see what i can do with it tonight thanks Kevin and Paul
- Sun Aug 12, 2012 1:50 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: kohler front pulley help
- Replies: 4
- Views: 3391
kohler front pulley help
im in the process of taking the engine apart on my 124 to rebiuld it and I need some help on how to take the pulley off the front off of the engine. Any suggestions are greatly appriciated
- Wed Aug 01, 2012 1:41 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: setting the governor on a cub 124
- Replies: 3
- Views: 5951
setting the governor on a cub 124
i recently replaced the brass nut that the governor shaft goes inside of and now I can't get the governor set right. It bogs down when I go up hills and revs up going downhill. I've tried moving the spring that connects to the governor arm to the throttle cable in almost all of the holes on the gove...
- Tue Jun 21, 2011 6:50 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 582 special rear end swap
- Replies: 5
- Views: 5442
Re: 582 special rear end swap
ok, and do you happen to have the measurements for the holes and the overall length for the driveshaft by chance? im a bad guesser when it comes to that kinda stuff lol. if you do thatd be great
- Tue Jun 21, 2011 6:05 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 582 special rear end swap
- Replies: 5
- Views: 5442
Re: 582 special rear end swap
Is that driveshaft longer than the the nf/wf tractors? and i was thinking, would i need a wf shifter to clear the fender pan? thanks for the info so far guys
- Tue Jun 21, 2011 3:02 pm
- Forum: CCC and MTD Built Cub cadets
- Topic: 582 special rear end swap
- Replies: 5
- Views: 5442
582 special rear end swap
i just bought a 582 special and id like to put 3 speed cast iron rear end in it. Do i need to drill new to drill new holes for the cast iron rear end? Where can i get a clutch? I think they are diffrent than the wf clutches. Thanks in advance!
- Thu Dec 16, 2010 10:37 pm
- Forum: The Coffee Shop
- Topic: $4100 CC 1200 on Ebay Yeah,right
- Replies: 13
- Views: 9440
Re: $4100 CC 1200 on Ebay Yeah,right
Thats quite the joke! and its not even a rare tractor. what an idiot
- Fri Dec 10, 2010 12:24 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 126 frozen up rearend
- Replies: 6
- Views: 5332
Re: 126 frozen up rearend
thanks Todd
- Fri Dec 10, 2010 10:58 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: honing an engine cylinder
- Replies: 8
- Views: 6886
Re: honing an engine cylinder
i never really looked at it that close,but i dont think there is much or a ring on it just going from memory.
- Fri Dec 10, 2010 10:56 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: 126 frozen up rearend
- Replies: 6
- Views: 5332
126 frozen up rearend
ive got the engine out of my 126 and i went to move the tractor the other day and the rearend seems to be froze up.i cannot put it in any gear and it doesnt roll freely. i never bothered to look inside it when it was warmer but if theres water in it, how can i melt it, besides with a small propane t...
- Thu Dec 09, 2010 12:19 pm
- Forum: Cub Cadets and Shooting the Breeze
- Topic: honing an engine cylinder
- Replies: 8
- Views: 6886
Re: honing an engine cylinder
ok i will.but the thing is that i will need a new piston as well so should i just go off of the standard piston size wherever i find it? thanks
- Thu Dec 09, 2010 11:23 am
- Forum: Cub Cadets and Shooting the Breeze
- Topic: honing an engine cylinder
- Replies: 8
- Views: 6886
honing an engine cylinder
ive got a k301 out of a 126 that i want to hone so it doesnt burn oil. The rod was broke when i bought it and havnt gotten to it till now and thought since its out i might as well do it. what i am wondering is what are the steps to go through to hone it out. I have heard you have to first oil up the...