Cub Cadet Collectors dot com

Hi all,

I installed a WYSIWUG editor that seems to work properly. upto this point none of them seemed to function well
WYSIWUG  =  what you see is what you get

IE no more <tag> etc.

You can bold italic underline etc. Just like you would in Word or your email

Try it out
dave
 

I feel like i have always had better luck with diggin down the bottom of my junk engine parts drawer and pulling out a nice old Delco Embossed coil with already attached oem kohler condenser vintage 1960 1970. Seems like i always end up fighting with new stuff. I think i have even had brand new kohl...

The transmissions on these 3000 series had numorious problems. The gear inside the charge pump explodes causing all functions to stop! Also some of these were prone to the differentials blowing up when the diff lock is used improperly. Keep the engines clean, if oil starts to leak the engine fins co...

According to this service bulletin. early charge pump pressure was 500 to 625 psi and was increased to 800 to 900psi during the 782 era. http://www.cubcadetcollectors.com/forum/app.php/dlext/details?df_id=358 I would have to think a 1650 would fall into the 500 to 625 range, unless they made another...

link to diagram

2072 Wiring Diagram

Tom is hitting everything on the money. they can be tricky to diagnose. And to top it off they can also trick you into thinking you have a good connection. Testing things with a Volt meter can sometimes show a good 12 volts at a test location- most people are like ok i got 12 volts there im good rig...

Ive heard these comments from years past. It may be a thing for the pullers. would have to ask some of those guys. Id be slightly concerned with clearance from the head to the piston. Ive always run the good metalic heat gasket, sprayed with copper coat. Along with a good true head, top of block cle...

So i had forgotten what this thread was all about cause it started so many years ago....

I have decided to start from page 1.... its been a long journey and now Im at page umm ugh 4!!

Still working on it, Hope i can retain enough for the Test@!

dave

Thanks for the support.... i think we have past the goalpost! FYI here is a snapshot of the forum billing So the typical is 14 bucks a month, there is one for 23 cause they changed the PHP and if you dont play with the Jones boys they charge you more. So that has been fixed. Also the one large one e...

How can we get more traffic here? What do we need to do? I try every day to point people over here. There is a wealth of info here.... but not the traffic? The forum costs about 250 bucks a year to run, Domains, hosting etc. In 2 years i have received $150 bucks towards $500 in costs. Which i am for...

Dave,

Na, no turbo on this one...it already cost enough money to build!

maybe on the next one. .....although i have said that a few times now. this is my 3rd diesel build.

The fender mounts for diesel supers are different then GT fender brackets. The front one is very similair just 1.125 inches taller. The rear ones are completely different then GT ones

Myself and joe went out on a mission many many years ago to make harnesses. we started with the ones that were the biggest problems. 1x67 and 1x89 due to the cloth covered wires... we sourced all new wire, ends, plastics everything. We later expanded and made harnesses for original to QL series. At ...

you can embed youtube.... by simply using the youtube button and inserting the video code "YfuSJ4yvS68"

Just about finished. Just a few more items and the 3 point hitch

i created a section for service bulletins... and started to upload them.

dave

Think maybe you mean a 364? i have one at my dads house. i wanna say its the same as the 450 451 etc. This topic has been up front lately as i just brought in a 551 that had a busted chute and was selling it almost the same day. So i did some reaserch on it and found the lower part for the 551 is st...

email send to the one registered in your profile

I have new ones in stock

159
PLUG
- Plug, Drain
KH-X-708-1 $33.65 4-6 business days 1
ouch!

I may have one in the drawer

have u located one?

Thanks for that writeup! Ive found the key to those pesky things is patience mostly! but as you mentioned in your writeup. one big help factor is digging all the dirt out of the hex hole... ive also found that using a nice new hex key each time helps... they do seem to wear. I also have a hex key th...

How do those compare to the $14 dollar ones on ebay? They seem identical? Isave tractors price is like 60 bucks? I have bought a few for 14 bucks...they seem to work good. But usually have to make a slight mod like drill out the thottle shaft hole for linkage.

interesting idea. I am not sure i have all the files we have here on my computer.... at least in normal format. The file names are all hashed on the server so its not quite as easy as just sucking them all out via FTP. And a good number of them would most likely need to be renamed as the file name d...

hey look the weatherman is back! thought maybe he retired.......

I do beleive the 450 will spin just a bit fas

Looks a little fishy like it went NLA acording to parts tree or mesicks... but its showing on cubcadet.com.
PN 732-3010

also looks like Marlin has some at IHCCW.com

Currently no way to upload and run a video file directly due to the massive size of a typical video. Been looking for sometime to possibly add such a thing. maybe. Till then you can use YouTube to upload and link to the youtube video using the "youtube" button above. If you hover over it, it gives i...

assume your on a phone?
IF its android, open gallery, open picture, then click on the pencil/crayon down at bottom, then the editor opens, then the 3 dots top right and click "resize" id select like 40 percent. and save.
if its Iphone.... im not sure but probably similair.