Cub Cadet Collectors dot com

You can make an adapter section of wiring to go between the two wiring sections and not cut any of the wiring up. Below is how adapter is wired.

There are other number cubs that have the same tranny, I check craig's list and sometimes find them. When one of these go bad there is wear to shift keys and gears so buying new parts is out the window.

THe usual problem with them is wear in the shift fork in tranny, as wear gets worse it shifting forward to reverse has a lot of slop it will jerk, harder the jerk the more sign of the wear. About the only fix I've found is find a donor.

Is pto switch off, on it won't do anything?

Trying to put std rearend from 1535 in my 1872, am having problem with shifter hitting battery box don't know why, had to put front two holes for rearend in frame, maybe puts rearend to high, maybe shifter different placement, has anyone else did this, any help would be great. Thanks

Vince If I remember right he made a special part tp put on flywheel with a pulley made on it. I have a aluminum creeper I'm going to use in mine. Are you sure about a overdrive that would make it faster and you will already gain some speed by the larger tires, I was thinking about a 10% underdrive s...

It wasn't a super but was 82 series very neatly done, I was told they thought it was Scott Murphy, doesn't seem to be a site member here. I want to do this but don't know much about hydraulics, pump size, pressure output reguired and other things needed even have a tractor to play with already put a...

Looks like a 982 only change is aluminum reareand, check rearend had a bad problem with coming loose and messing up holes in rearend other than that about the same were MTD made.

On adding hydraulics to std cub what kind of specs. would the pump have to have, flow ,output pressure. Thanks

I have a set of the 1" axles and carrier also to use or maybe pay for some the other, right now this on my want to try project list, subject to a lot of possiblites. I want to put this in a super frame setup with parts from a 1806. Still have a lot of the super to get rid of also for money for this....

I have a 1535 tranny according to what I've read on this site they have the 30mm axles, to put these into a older cast iron case the axle tubes have to have the end of axles tubes bored to a larger dia. for larger bearings. So what dia. do they need to be and is expensive to have done going to use s...

Found this.

I have manual that says the 190-401-100 post e-mail will send it to you don't kmow if its right one or not.
.

Try this http://www.ihcubcadet.com/IHCCFAQ/IH%20 ... S%20SN.htm

I saw a 10% underdrive on evilpay is this slower and whats a good price for one. Would this be enough to offset the 23" to 26" tire dia. difference? Looked these up on midwest cub looks like a bit to much cost for me. THANKS

I think the rear in my 1806 has a non-factory input shaft ( 3 speed transaxle) in it,it seems to run faster than it should, looked like someone had pulled with before I got. I don't know anything about these can you get one to make it run slower than factory want to put 26x12-12 on a tractor, so I w...

I'm not talking about the whole tractor, just the transaxle, power steering and maybe at a later date the hydraulics. I bought it for a project using part of it. Thanks

When it warms up enough I'm going to part my 1872 and I was wondering which way would be best try to sell the hydro rearend complete or axles and carrier, then hyrdo pump. That way shipping would be possible. Thanks

In all this talk of loaders nobody mentioned a Schwartz 1050 qt loader, found this in a cub options book, I don't remember anybody talking about one of these was this a item that never happened or wasn't liked very well?

What I need from this is driveshaft same lenght and is plate bolted to engine the same? Thanks

I have 1806 cub that I'm thinking about taking 18hp mag out (need for another tractor) and putting a 16hp briggs back in it. How much will have to be changed, motor is complete except pto? Thanks

How rare are pto for 582's? I'm considering using a 16hp briggs in a tractor but motor I have dosen't have one, from what I've seen on pto prices this could be a reason not use motor? If it's very high will probaly just sell motor. Thanks

Maybe his wife told him he had to sell, so he's trying

I rememder reading on the registry site about adding hydraulics to a manual transmission cub, it had a lot pictures and info about how they did it. Does anyone have any of this info or is that user here on this site? I'm considering doing this to one and will need all the help I can get. Thanks

Jess the motor you got back in the summer from me (in pieces) was from it. I got a 16hp briggs with it.

No, still still hunting that elusive 3 point.

Had been converted to a Onan performer that blowed up, are they points or mag?The guy that had told me he had a 16hp briggs that could be put in it, I bet that would've work out great. i have the rest of the parts for my project now they came is a one piece package package.

This tractor is missing motor and possibly other parts, last one of these I had was in bad shape ( I don't think it had a tight bolt in it and threw driveshaft out) this one is a unknown condition at this time it's futute will depend on condition. Thanks

I'm picking up a 1872 with no motor, was told it looks good but haven't seen it yet. I keep wanting to make a standard super. Whats the differnce in lenghts between regular and a super,what's creeper lenght so I can compare, I have a 1535 rearend with creeper? Would like to keep hydraulics but cost ...

Jess (JLaws) did.