Cub Cadet Collectors dot com

That 184 Lo-Boy is a nice rig!!!

Well...we all like pics...so here's a shot of my 108 out getting a little sun yesterday. Cleaned up the old tomato stalks from the tomato cages and hauled them off in the trailer, hauled some fish guts and slimey water off after cleaning a mess of crappie. :D You can see the smoke in the pic if ya l...

Nice find, Vince!!!

The clutch was not working very well in my 86 after I got it running so I tore the drive line down to see what needed to be done...The Clutch plates were in pretty bad shape after sitting up for 3+ years. I decided I would try and clean them up a bit. DISCLAIMER: Try this at your own risk. I am not ...

J Hayes wrote:How did you get that water mark to show up in pic just above the seat ?

I made the water mark with a transparent background, I then copy it and paste it into a new layer and adjust the opacity of that layer for the way I want it to look.

Thanks for the tip Scott!

Here's a pic of my 86 in the yard today

After I got my 86 running and then had to rework the driveline in it...everything was just fine and then the intake lifter/tappet stuck in it.... :banghead: I tried to get it unstuck for awhile with no luck...another project came up...I had to refinish some antique furniture for my granddaughter tha...

Your engine may be like this K301. Hope this helps

According to Kohler Specs, here are the numbers (all measurements in inches) K241 (10hp) Bore and Stroke = STD. 3.251" .010" 3.261" .020" 3.271" .030" 3.281" x 2.875" Cubic inch displacement = 23.85 Connecting Rod {Big end Dia. Max} the same on all three STD. 1.5015" .010" 1.5115" .020" 1.5215" .030...

vince_o wrote:Goat

I told you it was worn out

Yeah ya did!! Ya think maybe a .030" piston and rings thrown in there might work...

The CC 108 that I bought was smoking really bad, as some of you know...well, I pulled the head today and the motor has already been bored to .020" over....and now I know why it is smoking!! The cylinder measures 3.271" @ top 3.276" @ bottom 3.285" @ middle :o I am going to re-sleeve this block. Wher...

Goat I dont now if the 8hp is like the 7hp to set the air gap, but if they need adjusted, you may have to take them out and grind them. BUT The problem you are listing sounds like maybe some carbon in the guide or on the valve. Are you running the MMo in the fuel? Geezer or Paul B would be the ones...

Been rebuilding the drive line for my Cub cadet 86 this week, got it put back together today and cranked the CC 86 up.... everything is working like new, rode her around the yard for about 7-8 minutes and she just shut off..just like you turned the key off...did not make any noises..nothing..just sh...

I sure do thank you all for the help, info, and tips.. :thumbsup: :notworthy: I found the coiled spring pins (heavy duty) cheaper at McMaster-Carr. I also found some compression springs there and if somebody knows the specs on the teaser spring, McMaster-Carr should be a source for those too. They a...

Well my son and I pulled the 108 in the shop this morning and removed the carb, tore it down, put it in some carb soak and the float went to the bottom......got the soldering iron out, fixed the hole in the float, tested it by holding under water for 3 minutes..no leak . Put the carb back together, ...

Started out this morning working on the 86...pulled the carb, tore it down, soaked it in some carb soak and cleaned it up real good, had to replace the bowl gasket. Had to replace the hot wire to the coil, spark plug looked good..the gap was way off, got it all set and re-installed. checked the poin...

:lol: ...Thanks guys! Vince seems to be a good guy..ya know we all have our little quirks... :lol: I am working on the 86 and need to replace the "hot" (red) wire to the coil...The old one is frayed and some insulation is broken and missing. I have some 14 guage on hand. Does it need to be heavier t...

Hey folks.. vince_o told me about this place..so I figured it was okay since he was here 8-) :D Been lurkin a few days and reading alot and went yesterday and bought my first ever Cub Cadet. Got a deal on some CC's from an elderly guy that had a stroke a couple years ago and suffered some damage to ...