Cub Cadet Collectors dot com

SSSSSSSSWEET !!

dag1450 wrote:... Maybe u could clarify what year or models for that yellow u were talking about ? Thanks for the tip. Dave

Dave, so far, I have been working exclusively on IH-produced narrow frames, and have a few wide frames waiting in the wings and/or for parts.

Cheers,

My method for painting with rattle cans is: 1. primer (usually grey) 2. two coats of ivory/almond of any brand 3. last coat in CC colour from the dealership. If the part is not really seen, I don't even bother. The rattle cans from the CC dealer are very expensive here, so the above method works wel...

Very, very nice execution!

Wow; it must not rain IHCCs in the UK...!!?

Welcome aboard,

Pretty darn cool!

Did you make the fenders, or retrofit from something else?

Cheers,

I proceeded to finish installing the clutch completely, to make sure there would be no issues. (It's easy enough to remove at this point if it gets in the way.) Well, I ran into a glitch: When I fitted the clutch without securing the (rear) shaft collar (but with the engine bolted in), everything wa...

You joined the right place...!

Hello OhioBinder,

The repair plate I have has the following interior dimensions: 3/4 x 1 3/16 inches.

Hope this helps,

Gorgeous!!

Make sure the part that receives these springs and pucks is not worn out...

I still have the VHS tape that came with the purchase of my 2185, but it's an owner video, not a shop video...

I got the repair plates from XtremeMotorWorks... Made a mark where the new part needed to be welded and cut off the old metal.

Tim,

You may be interested in the 'Hydraulic Pump and Undercarriage Assembly' part/assembly of the 190-825-101 hydraulic tiller...

Ciao,

Wheel weights for the occasional FL snowstorm, I see...

Good luck with your tune-up; welcome,

IMGP4855.JPG IMGP4853.JPG Well, guess what?! That bracket works after all... Looking at pics before dismantling partially showed how things were mounted, which is as in the pic above. (Tried all I can to make the pic in the correct direction, but it gets rotated everytime I upload it... :x I gave u...

http://farmallparts.com/products/?view= ... t_id=27527

That might be a good choice; wish it started at 0 instead of 8; price seems very reasonable.

I'll have to look into the difference in wiring (if any) if I go the volt indicator route...

Cheers,

I'll be installing these myself in the not too distant future; is blue loctite a good idea...?

Hey all, This seemed like an appropriate older thread to post my question... I'd like to test an old charge indicator (a.k.a. amp meter, volt meter, ammeter) out of the tractor to see if it's any good to use on a tractor in the future. Is there a way to do this with simple tools? The old part I have...

Thanks for the tip guys; it's on my to-do list to play around with that bracket some more, but with the engine in and the clutch assembly held at both ends of the shaft. I'll then see if one of the four possible positions of that bracket (it has a pair of mounting holes on each side) will work. The ...

Thanks for the pic Dave, and thanks for the observation, Jess. I'm noticing that in Dave's pic, that would locate the yoke a fair bit higher than in my pic... Well, I guess I will have to: - fit the clutch with the engine, and see if by luck the clutch arm will line up with that heavy-duty bracket (...

FWIW, I have observed that, generally speaking, ATV tires are less expensive than Ag tires for comparable quality.

Well, wadaya know...?! A p.o. modification... I don't have access to a gear drive narrow-frame machine to look at how things are supposed to be... Could someone pls. post a pic or two of how things are supposed to be? My (now powder-coated) pedestal does not have anything to receive the yoke that th...

IMGP4847.JPG As you can see, I started test-fitting the clutch assembly without the engine. I haven't done anything to the bracket that holds the clutch lever; I just cleaned it up and painted it. It looks cockeyed, but that's how it came off the 122. Does it look 'normal'? Also, why does that heav...

Looks fantastic! Was it tricky to figure out the piece of sheet metal that is welded to the fender and connects to the seat support? Any tips or things learned when performing that particular fabrication? (I can't see a good look of the fender connecting to the footrest, but I assume it's there.) I ...

Thanks Kenneth!

Well... I finally have something to show... :oops: (We did do a major house reno in 2013...) As you can see, this will be pretty much an all-white tractor. The rear tires are ATV tires I got at a better price than tractor ag tires. I splurged on the front tri-rib. (I can't say enough about the extra...

Got back to this tranny during the Christmas break... (I also got an engine 75% rebuilt last winter...)

Nice looking rigs !!