Cub Cadet Collectors dot com

They must be FREE!!!

Hi chum lee!!!

Joe Got ya. How are the Connecticut boys doing up there? I'm tired of this crappy weather. Good thing the loader is here to make snow piles about 7 feet tall.

Was it a 42" and made into a 54"? Whats with the different heights of the blade or is it just an illusion?

Joe,
Whats going on with that blade?

Paul, I would use graphite which is more of a dry lube. Oily lube will attract dirt. I've tried to get a spray in there before with no luck.I cleaned it twice before replacing it with a new one. I've put in a new starter I think it was a DR starter on ebay. It got good reviews. It's been it there 2 ...

No they wont unless you modify them.

Look on craigslist for quad take offs. I buy them all the time. Last set of 4 was $100 for new take offs.

Todd,
Looks good. But that's an awful small snow plow you have

kevin, here's a pix of the pump bracket I made. I've slotted a couple holes for adjustment as you said. The pump pulley is about 3 to 4 inches I will measure for you in the next couple days. the belt is not that tight because you have almost 3/4 of the belt engauged so it should not slip on you. Min...

Your BIG Mike I'm littleLLITTLE Mike

The triangular tube was not cut when I did mine. That's how I determined where I was going to put the upright. I think you might be alright in the middle of the foot rest. If I ever take the loader off I will push it forward about the same area as you mentioned.

Kevin,
No problem make sure the subframe is forward enough to get the weight right. wish I had put mine a little more forward. Also make sure you have the support rods from the upright to the front. Here a couple side pixs.
Mike

Kevin my Kwik way has the valve on the r/side and reservoir is the r/side upright. Its in the garage and easy to get picture if you need them. Just let me know. I can text them or email them to you. Mike

Model 71 I would say.

Put a spark plug tester on. Run it and watch the spark. See if you loose it. Buy 1 of these great tool.

Does anyone know how the fields are out there. I know they are like Riverside was but are they muddy?

That is camber. Not sure what the correct spec is, but sounds like you have a bent spindle. I would think it should only be couple degres for turning.

Better you then us!

Where is all the white stuff on the ground..

Lew your right solid pin.

Is the engine right. Maybe its cocked a little in the frame

100!! Lol that's for All the bad weather.

I put 26x12x12 under my 149 loader. I had to shim up the fender pan 1/4". I also got wider wheels.The 1811 got 26x10x12 without mods. I paid $100 for 4 new tires (take offs of a quad) off of craigslist. I've gotten 3 sets off of there so far. More then enough traction.

I would go buy the creeper and oil bath. You wont find it any cheaper.
Here's what mine started with.They where easy to find back then but parts where hard to find. 10 years ago. Here's what it ended up like. Not great paint job (1st for me)

I have pics from as far back as 09 but can't find any thing earlier I have I more hd to check out

All right who's going? I think I'm still in.

Geezer,
That was a cool thing to witness. I'm not saying any ones name but I think they fessed up. That was a funny weekend. I'll have to look. That was 3 cps ago I think.

Most of the carbs are self venting so I think your always going smell gas. But do check for a gas leak. It's like 1 or 2 drops is going to stink the whole place up. I would also put in a CO detector if you haven't already. As for venting gable end vents or fans with louvers. Ridge vent if positble. ...

BB,
When I made mine I just used a 5/8 drill bit. .150 is not much