Parts by Jeff-sleeve hitch, PTO buttons and custom parts

This page is for our vendors that help us maintain our great little tractors. Support Them!

Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Fri Jul 26, 2013 5:52 pm

I make a large variety of parts for cub cadets. I can make custom parts too. All parts are made by myself, I'm a machinist / fabricator with over thirty years experience.

Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps
Image

$120 shipped
$135 shipped with one set of drilled and one set of slotted straps

Add a lift pin for an additional $10
add a triple drilled lift pin for an additional $15
Extended length to clear tiller mount add $5
I can make these custom length if needed.

~~~~~~~
double hole rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image
$17 plus shipping
( $10 with sleeve hitch adapter order )
~~~~~~~~~
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image

$22 plus shipping
( $15 with sleeve hitch adapter order )

~~~~~~~~~~~~~~~~~~




Height adjuster knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.
Image
Image
$23 shipped
~~~~~~~~~~~

1/2-13NC threaded rod for use with above knob ( or factory knob )
Image
$9 shipped
~~~~~~~~~

Brass PTO button
Image
$8.50 each shipped

~~~~~~~

Pair of "frankenstein" bolt and nuts for WF rear lifts
Image
$32 shipped

~~~~~~~~~

Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.
Image

$17 shipped

~~~~~~~~~~~

Wide frame solid motor mounts with washers, Grade 8 flanged bolts and nylock nuts.

$43 shipped for set of four.

Image


~~~~~~~~~~~
Headlight rings for 1X2/1X3/1X4/1X5
Image

$32 per pair plus shipping

~~~~~~~~~~~

Original style lift pin
Image

$22 plus shipping

~~~~~~~~~~~~~

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread
Image

Image

Image

I'll also sell just the bolt and castle nut too


Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping



~~~~~~~~~~~

Narrow Frame rear lift attachment bracket for lift handle. ( wide frame brackets available too )
Image

$22 plus shipping

~~~~~~~~

Image

Wide Frame lift brackets also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

Image

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PTO pulley puller

The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier.
Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.

Image

It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)
Image

$22 each plus shipping

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.

Image

$52 each or $97 for the pair shipped ( USA )

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Image

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox or to manual transmission.

Image

$25 plus shipping

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


If you order more than one item, I will do my best to keep shipping costs as low as possible.


All parts manufactured by me and mailed from the Palm,PA post office
Please either PM or email me
Thanks
Jeff
Last edited by Jeff in Pa on Sun Mar 01, 2015 10:01 am, edited 11 times in total.
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Tue Jan 07, 2014 2:55 pm

Just added headlight rings :beer:
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby tbdavis123 » Sat Jan 11, 2014 8:32 am

Jeff - do you by chance make lift pins for the Originals?
tbdavis123
 
Posts: 101
Images: 0
Joined: Fri Jan 03, 2014 7:29 pm
City and State: Greenfield, IN
First and Last Name: Terry Davis

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sat Jan 11, 2014 5:07 pm

tbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?


I will as soon as dimensions are verified :beer:

Jeff
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sun Jan 19, 2014 11:44 am

tbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?


Yes I do

~~~~~~~~~~~

Original style lift pin
Image

$22 plus shipping

~~~~~~~~~~~~~

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread
Image

Image

I'll also sell just the bolt and castle nut too
Image

Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:38 pm, edited 1 time in total.
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sun Feb 23, 2014 6:11 pm

Narrow Frame rear lift attachment bracket for lift handle.
Image

$22 plus shipping

~~~~~~
~~~~~~~~

Image

Wide Frame lift brackets also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

Image
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:39 pm, edited 1 time in total.
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby edc » Sun Feb 23, 2014 6:34 pm

Jeff, Id like to buy to brass wear buttons
edc
 
Posts: 1
Joined: Sun Oct 21, 2012 8:52 pm
City and State: grand island, NY
First and Last Name: Ed Colan

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sat Apr 26, 2014 1:58 pm

Just added PTO pulley pullers

Thanks
Jeff
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby F Currier Northern Maine » Sun Apr 27, 2014 6:03 pm

Jeff, your PTO pulley puller is so close to what I've been trying to configure - and I can't make one for your price. I've PM'd you because my email isn't set up to just click on your address. I think you've got the answer to pulling one of them without damaging/bending it and I know what they cost new! Ouch, that hurt! :)
F Currier Northern Maine
 
Posts: 42
Joined: Fri Sep 24, 2010 11:19 am
City and State: Portage Lake, Maine
First and Last Name: Frank A. Currier

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby l palma » Sun Apr 27, 2014 8:53 pm

Frank,
I have one of those and it works great!!
I even have the one one for the welded baskets.
You do not have the required permissions to view the files attached to this post.
User avatar
l palma
 
Posts: 705
Joined: Mon Sep 06, 2010 9:46 am
City and State: Montague, N.J.
First and Last Name: Lew Palma

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby PTWannaHave » Tue Apr 29, 2014 9:01 am

Hello Jeff,

Ever thought of designing/building a better PTO pulley? The stock version is flimsy/thin:

- makes it prone to distortion
- doesn't contribute to engine torque (but I assume it could with weight)
- is most likely not balanced
- without your removal tool, easily bent during removal
- does not seem to always allow enough space for the bolt head that holds the S/G bracket

Just some thoughts as I will be putting the stock PTO pulley back on a fresh rebuild in the near future...

Ciao,
PTWannaHave
PTWannaHave
 
Posts: 285
Images: 21
Joined: Wed Apr 11, 2012 12:39 pm
City and State: Richmond, Ontario
First and Last Name: Ben Michaud

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby F Currier Northern Maine » Mon May 05, 2014 8:55 pm

Thanks, Jeff !! The one on the right is as far as I'd got - and I don't weld! (Now I can go paint it)!
You do not have the required permissions to view the files attached to this post.
F Currier Northern Maine
 
Posts: 42
Joined: Fri Sep 24, 2010 11:19 am
City and State: Portage Lake, Maine
First and Last Name: Frank A. Currier

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sun Jun 01, 2014 11:08 am

Now available--90* gear box shafts


90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.

Image

$52 each or $97 for the pair shipped ( USA )

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:39 pm, edited 1 time in total.
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby vince_o » Sat Jun 07, 2014 9:28 pm

Jeff you do such nice work!
"It's a damn poor mind that can only think of one way to spell a word."
-Andrew Jackson
User avatar
vince_o
Moderator
 
Posts: 2035
Joined: Mon Sep 06, 2010 3:20 am
City and State: Pickens, SC
First and Last Name: Vince Ochiuto

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sun Aug 03, 2014 6:40 pm

Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image

$22 plus shipping
( $15 with sleeve hitch adapter order )
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:40 pm, edited 1 time in total.
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Wed Oct 01, 2014 7:18 pm

Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Image
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:40 pm, edited 1 time in total.
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby tinnerlee » Thu Nov 20, 2014 5:45 pm

I would like to buy a pto pulley puller how do I order one thanks
tinnerlee
 
Posts: 1
Joined: Wed Nov 19, 2014 9:12 pm
City and State: oskaloosa, IA
First and Last Name: mike beadle

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby LFR » Mon Nov 24, 2014 9:36 pm

:email:
Cub cadets are working Not sittin in barns, save them all!
LFR
 
Posts: 349
Images: 7
Joined: Fri Jan 17, 2014 4:28 pm
City and State: Boyne City, MI
First and Last Name: Lorin Burch

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby Jeff in Pa » Sat Feb 28, 2015 3:29 pm

Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox.

Image

$25 plus shipping
125 & 125 with hydraulic lift
User avatar
Jeff in Pa
 
Posts: 633
Images: 0
Joined: Sun Sep 12, 2010 8:06 am
City and State: Zionsville,PA
First and Last Name: Jeff Derstine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Postby jturner008 » Mon Apr 24, 2017 7:43 pm

Jeff; I am interested in the sleeve hitch are they still available contact me a Jturner008@centurylink.net Thanks Jim Turner
jturner008
 
Posts: 1
Joined: Wed Apr 12, 2017 4:23 pm
City and State: Sheldon Mo
First and Last Name: Jim Turner


Return to Our Vendors for Parts Used and New

Who is online

Users browsing this forum: No registered users and 1 guest