Xtreme Motorworks - Your online source for Hitches, Dual Wheel Adaptors, Category 0 - 3 Point Parts and Hitches and tons more! We make parts for most Cub Cadet Tractors and are adding new parts all the time.
Visit our web site: http://www.xtrememotorworks.com
Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Parts
-
- Posts: 5
- Joined: Sat Sep 11, 2010 2:00 am
- First and Last Name: Aaron Schmidt
- Location: Detroit Lakes, MN
Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Parts
Last edited by aschmidt on Sat May 19, 2012 8:19 pm, edited 1 time in total.
- J Hayes
- Posts: 919
- Joined: Mon Sep 06, 2010 6:20 pm
- First and Last Name: Jim Hayes
- Location: Apollo Pa
Re: Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Par
Welcome Aaron Glad ya made it back !
My mind wants a Divorce ?? .
-
- Posts: 5
- Joined: Sat Sep 11, 2010 2:00 am
- First and Last Name: Aaron Schmidt
- Location: Detroit Lakes, MN
Re: Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Par
Reproduction Brinly Gard-n-Cart
Just got these done and they are a spitin image of the original ones. They mount on the Originals, 70's and 100, 102,104and maybe some otheres
Kits come unpainted and ready to paint.
---------------------------------------------------------------------------------------------
Cub Cadet 82 Series 3 Point
Reproduction Category 0 - 3 Point lift system. The kit is designed to work off of the single deck lift system. You can leave your deck on and lock it in the up position while using your 3 point accessories. Complete kit. Retrofit to fit more tractors than the original 190-389 kit by Cub Cadet.
Some major improvements were made to this kit:
1. Double width bushings on the rock shaft to prevent premature wear and failure over time of the main plate.
2. Dual lower holes for the drag link pins, allows you to tailer the height of your lift and change how your equipment pulls.
3. Hole in the middle of the back plate allows you to get to the oil fill / check hole without having to dismantle the 3 point.
4. Holes in the upper left corner on the back face to allow quick attach hydraulics to be added - re-route your front ones to the rear or add in a set.
5. The upper 3rd link attachment brackets are welded on instead of (2) 3/8" bolts holding them on. Much stronger than stock.
6. If you have a newer tractor, the hole for the rear deck adjustment rod it pre-drilled and located.
7. Dual lower hitch holes to accommodate the 3 and 5 bolt hitches - depending if you have the aluminum or cast iron rear end.
8. Whole rear frame is made out of a whole guage heavier material.
Will not work on tractors with PTO. Receiver hitch sold seperately.
---------------------------------------------------------------------------------------------
Sleeve Hitch Kits - $158 includes shipping to your door.
Reproduction of the original sleeve hitch used on many cub cadets - Tractor Bracket sold seperately.
---------------------------------------------------------------------------------------------
Snow Thrower Wings - $78 includes shipping to your door.
Adds 4" to each side of the QA-36 and QA-42 Snow Throwers. Hardware included. Bolt on kit.
---------------------------------------------------------------------------------------------
Drift Cutters - $58 includes shipping to your door.
Drift Cutters for the QA-36 and QA-42 Snow Throwers. Hardware included. Bolt on kit.
Just got these done and they are a spitin image of the original ones. They mount on the Originals, 70's and 100, 102,104and maybe some otheres
Kits come unpainted and ready to paint.
---------------------------------------------------------------------------------------------
Cub Cadet 82 Series 3 Point
Reproduction Category 0 - 3 Point lift system. The kit is designed to work off of the single deck lift system. You can leave your deck on and lock it in the up position while using your 3 point accessories. Complete kit. Retrofit to fit more tractors than the original 190-389 kit by Cub Cadet.
Some major improvements were made to this kit:
1. Double width bushings on the rock shaft to prevent premature wear and failure over time of the main plate.
2. Dual lower holes for the drag link pins, allows you to tailer the height of your lift and change how your equipment pulls.
3. Hole in the middle of the back plate allows you to get to the oil fill / check hole without having to dismantle the 3 point.
4. Holes in the upper left corner on the back face to allow quick attach hydraulics to be added - re-route your front ones to the rear or add in a set.
5. The upper 3rd link attachment brackets are welded on instead of (2) 3/8" bolts holding them on. Much stronger than stock.
6. If you have a newer tractor, the hole for the rear deck adjustment rod it pre-drilled and located.
7. Dual lower hitch holes to accommodate the 3 and 5 bolt hitches - depending if you have the aluminum or cast iron rear end.
8. Whole rear frame is made out of a whole guage heavier material.
Will not work on tractors with PTO. Receiver hitch sold seperately.
---------------------------------------------------------------------------------------------
Sleeve Hitch Kits - $158 includes shipping to your door.
Reproduction of the original sleeve hitch used on many cub cadets - Tractor Bracket sold seperately.
---------------------------------------------------------------------------------------------
Snow Thrower Wings - $78 includes shipping to your door.
Adds 4" to each side of the QA-36 and QA-42 Snow Throwers. Hardware included. Bolt on kit.
---------------------------------------------------------------------------------------------
Drift Cutters - $58 includes shipping to your door.
Drift Cutters for the QA-36 and QA-42 Snow Throwers. Hardware included. Bolt on kit.
Last edited by aschmidt on Sat May 19, 2012 8:18 pm, edited 1 time in total.
- red82s
- Posts: 126
- Joined: Mon Sep 06, 2010 2:45 pm
- First and Last Name: Adrian Gitch
- Location: Paris, KY
Re: Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Par
Aaron asked if I would post a pic of his Cat 0 hitch and tool box I just recently installed on the 782. All I can say is "Awesome quality work"!
Adrian
- Jlaws
- Posts: 1141
- Joined: Sun Sep 05, 2010 10:14 pm
- First and Last Name: Jess Laws
- Location: Independence , Ky
Re: Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Par
I've bought three of his Cat 0 hitch's for my 982's at different times over the past five years and they all were of great quality . He's made improvements with each one I've purchased , they keep getting better and better .
I see a lot of cub cadets while going down the tracks , its a shame I can't pull over and ask about them .
-
- Posts: 5
- Joined: Sat Sep 11, 2010 2:00 am
- First and Last Name: Aaron Schmidt
- Location: Detroit Lakes, MN
Re: Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Par
Thanks Guys, got some new stuff that people have been asking for.
Snowblower lift bracktes... fits cyclops and up... Original LIft Rods - Steel and Stainless Steel
Snowblower lift bracktes... fits cyclops and up... Original LIft Rods - Steel and Stainless Steel
-
- Posts: 5
- Joined: Sat Sep 11, 2010 2:00 am
- First and Last Name: Aaron Schmidt
- Location: Detroit Lakes, MN
Re: Xtreme Motorworks / Cat 0 Parts, Dual Wheels, Custom Par
Lots of new parts and FREE shipping for BLACK FRIDAY thu CYBER MONDAY!