Parts by Jeff-sleeve hitch, PTO buttons and custom parts

This page is for our vendors that help us maintain our great little tractors. Support Them!
Post Reply
User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

I make a large variety of parts for cub cadets. I can make custom parts too. All parts are made by myself, I'm a machinist / fabricator with over thirty years experience.

Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps
Image

$120 shipped
$135 shipped with one set of drilled and one set of slotted straps

Add a lift pin for an additional $10
add a triple drilled lift pin for an additional $15
Extended length to clear tiller mount add $5
I can make these custom length if needed.

~~~~~~~
double hole rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image
$17 plus shipping
( $10 with sleeve hitch adapter order )
~~~~~~~~~
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image

$22 plus shipping
( $15 with sleeve hitch adapter order )

~~~~~~~~~~~~~~~~~~




Height adjuster knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.
Image
Image
$23 shipped
~~~~~~~~~~~

1/2-13NC threaded rod for use with above knob ( or factory knob )
Image
$9 shipped
~~~~~~~~~

Brass PTO button
Image
$8.50 each shipped

~~~~~~~

Pair of "frankenstein" bolt and nuts for WF rear lifts
Image
$32 shipped

~~~~~~~~~

Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.
Image

$17 shipped

~~~~~~~~~~~

Wide frame solid motor mounts with washers, Grade 8 flanged bolts and nylock nuts.

$43 shipped for set of four.

Image


~~~~~~~~~~~
Headlight rings for 1X2/1X3/1X4/1X5
Image

$32 per pair plus shipping

~~~~~~~~~~~

Original style lift pin
Image

$22 plus shipping

~~~~~~~~~~~~~

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread
Image

Image

Image

I'll also sell just the bolt and castle nut too


Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping



~~~~~~~~~~~

Narrow Frame rear lift attachment bracket for lift handle. ( wide frame brackets available too )
Image

$22 plus shipping

~~~~~~~~

Image

Wide Frame lift brackets also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

Image

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PTO pulley puller

The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier.
Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.

Image

It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)
Image

$22 each plus shipping

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.

Image

$52 each or $97 for the pair shipped ( USA )

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Image

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox or to manual transmission.

Image

$25 plus shipping

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


If you order more than one item, I will do my best to keep shipping costs as low as possible.


All parts manufactured by me and mailed from the Palm,PA post office
Please either PM or email me
Thanks
Jeff
Last edited by Jeff in Pa on Sun Mar 01, 2015 10:01 am, edited 11 times in total.
125 & 125 with hydraulic lift

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Just added headlight rings :beer:
125 & 125 with hydraulic lift

tbdavis123
Posts: 101
Joined: Fri Jan 03, 2014 7:29 pm
First and Last Name: Terry Davis
Location: Greenfield, IN

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by tbdavis123 »

Jeff - do you by chance make lift pins for the Originals?

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

tbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?
I will as soon as dimensions are verified :beer:

Jeff
125 & 125 with hydraulic lift

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

tbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?
Yes I do

~~~~~~~~~~~

Original style lift pin
Image

$22 plus shipping

~~~~~~~~~~~~~

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread
Image

Image

I'll also sell just the bolt and castle nut too
Image

Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:38 pm, edited 1 time in total.
125 & 125 with hydraulic lift

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Narrow Frame rear lift attachment bracket for lift handle.
Image

$22 plus shipping

~~~~~~
~~~~~~~~

Image

Wide Frame lift brackets also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

Image
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:39 pm, edited 1 time in total.
125 & 125 with hydraulic lift

edc
Posts: 1
Joined: Sun Oct 21, 2012 8:52 pm
First and Last Name: Ed Colan
Location: grand island, NY

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by edc »

Jeff, Id like to buy to brass wear buttons

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Just added PTO pulley pullers

Thanks
Jeff
125 & 125 with hydraulic lift

F Currier Northern Maine
Posts: 42
Joined: Fri Sep 24, 2010 11:19 am
First and Last Name: Frank A. Currier
Location: Portage Lake, Maine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by F Currier Northern Maine »

Jeff, your PTO pulley puller is so close to what I've been trying to configure - and I can't make one for your price. I've PM'd you because my email isn't set up to just click on your address. I think you've got the answer to pulling one of them without damaging/bending it and I know what they cost new! Ouch, that hurt! :)

User avatar
l palma
Posts: 738
Joined: Mon Sep 06, 2010 9:46 am
First and Last Name: Lew Palma
Location: Montague, N.J.

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by l palma »

Frank,
I have one of those and it works great!!
I even have the one one for the welded baskets.
Attachments
20140410_101034.jpg
20140410_101034.jpg (810.63 KiB) Viewed 13373 times

PTWannaHave
Posts: 295
Joined: Wed Apr 11, 2012 12:39 pm
First and Last Name: Ben Michaud
Location: Richmond, Ontario

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by PTWannaHave »

Hello Jeff,

Ever thought of designing/building a better PTO pulley? The stock version is flimsy/thin:

- makes it prone to distortion
- doesn't contribute to engine torque (but I assume it could with weight)
- is most likely not balanced
- without your removal tool, easily bent during removal
- does not seem to always allow enough space for the bolt head that holds the S/G bracket

Just some thoughts as I will be putting the stock PTO pulley back on a fresh rebuild in the near future...

Ciao,
PTWannaHave

F Currier Northern Maine
Posts: 42
Joined: Fri Sep 24, 2010 11:19 am
First and Last Name: Frank A. Currier
Location: Portage Lake, Maine

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by F Currier Northern Maine »

Thanks, Jeff !! The one on the right is as far as I'd got - and I don't weld! (Now I can go paint it)!
Attachments
Jeff Derstine Puller 001.JPG
Jeff Derstine Puller 001.JPG (491.69 KiB) Viewed 13319 times

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Now available--90* gear box shafts


90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.

Image

$52 each or $97 for the pair shipped ( USA )

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:39 pm, edited 1 time in total.
125 & 125 with hydraulic lift

User avatar
vince_o
Moderator
Posts: 2045
Joined: Mon Sep 06, 2010 3:20 am
First and Last Name: Vince Ochiuto
Location: Pickens, SC

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by vince_o »

Jeff you do such nice work!
"It's a damn poor mind that can only think of one way to spell a word."
-Andrew Jackson

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image

$22 plus shipping
( $15 with sleeve hitch adapter order )
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:40 pm, edited 1 time in total.
125 & 125 with hydraulic lift

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Image
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:40 pm, edited 1 time in total.
125 & 125 with hydraulic lift

tinnerlee
Posts: 1
Joined: Wed Nov 19, 2014 9:12 pm
First and Last Name: mike beadle
Location: oskaloosa, IA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by tinnerlee »

I would like to buy a pto pulley puller how do I order one thanks

LFR
Posts: 351
Joined: Fri Jan 17, 2014 4:28 pm
First and Last Name: Lorin Burch
Location: Boyne City, MI

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by LFR »

:email:
67 Case 155, 66 Colt 2310, 68 John Deere 110w/ haban sickle bar mower, 59 simplicity 700 wonderboy, 62 allis Chalmers b1, Fairbanksmorse 3 wheel, 1944 McCormick peering O4, H, 1948 Farmall Cub, C.

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox.

Image

$25 plus shipping
125 & 125 with hydraulic lift

jturner008
Posts: 2
Joined: Wed Apr 12, 2017 4:23 pm
First and Last Name: Jim Turner
Location: Sheldon Mo

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by jturner008 »

Jeff; I am interested in the sleeve hitch are they still available contact me a Jturner008@centurylink.net Thanks Jim Turner

BearKiller
Posts: 180
Joined: Wed Nov 07, 2012 12:27 am
First and Last Name: George Riley
Location: Poverty Springs KY 2018 Wettest State in the Nation

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by BearKiller »

Jeff in Pa wrote: ~~~~~~~~~

Brass PTO button
Image
$8.50 each shipped

~~~~~~~
>>> EMERGENCY <<< !
Are these still available ?
As best I remember, I bought three from you (or somebody) a few years ago; the first one is getting thin and I have tore this place apart trying to find where I stashed the extras.
How do I order ?
Do you do PayPal ?

User avatar
Jeff in Pa
Posts: 665
Joined: Sun Sep 12, 2010 8:06 am
First and Last Name: Jeff Derstine
Location: Zionsville,PA

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Post by Jeff in Pa »

Best way to contact me is email.

I PM'd you and yes, I can accept paypal

Jeff
125 & 125 with hydraulic lift

Post Reply