Page 1 of 1

Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Fri Jul 26, 2013 5:52 pm
by Jeff in Pa
I make a large variety of parts for cub cadets. I can make custom parts too. All parts are made by myself, I'm a machinist / fabricator with over thirty years experience.

Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps
Image

$120 shipped
$135 shipped with one set of drilled and one set of slotted straps

Add a lift pin for an additional $10
add a triple drilled lift pin for an additional $15
Extended length to clear tiller mount add $5
I can make these custom length if needed.

~~~~~~~
double hole rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image
$17 plus shipping
( $10 with sleeve hitch adapter order )
~~~~~~~~~
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image

$22 plus shipping
( $15 with sleeve hitch adapter order )

~~~~~~~~~~~~~~~~~~




Height adjuster knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.
Image
Image
$23 shipped
~~~~~~~~~~~

1/2-13NC threaded rod for use with above knob ( or factory knob )
Image
$9 shipped
~~~~~~~~~

Brass PTO button
Image
$8.50 each shipped

~~~~~~~

Pair of "frankenstein" bolt and nuts for WF rear lifts
Image
$32 shipped

~~~~~~~~~

Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.
Image

$17 shipped

~~~~~~~~~~~

Wide frame solid motor mounts with washers, Grade 8 flanged bolts and nylock nuts.

$43 shipped for set of four.

Image


~~~~~~~~~~~
Headlight rings for 1X2/1X3/1X4/1X5
Image

$32 per pair plus shipping

~~~~~~~~~~~

Original style lift pin
Image

$22 plus shipping

~~~~~~~~~~~~~

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread
Image

Image

Image

I'll also sell just the bolt and castle nut too


Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping



~~~~~~~~~~~

Narrow Frame rear lift attachment bracket for lift handle. ( wide frame brackets available too )
Image

$22 plus shipping

~~~~~~~~

Image

Wide Frame lift brackets also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

Image

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PTO pulley puller

The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier.
Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.

Image

It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)
Image

$22 each plus shipping

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.

Image

$52 each or $97 for the pair shipped ( USA )

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Image

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox or to manual transmission.

Image

$25 plus shipping

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


If you order more than one item, I will do my best to keep shipping costs as low as possible.


All parts manufactured by me and mailed from the Palm,PA post office
Please either PM or email me
Thanks
Jeff

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Tue Jan 07, 2014 2:55 pm
by Jeff in Pa
Just added headlight rings :beer:

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sat Jan 11, 2014 8:32 am
by tbdavis123
Jeff - do you by chance make lift pins for the Originals?

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sat Jan 11, 2014 5:07 pm
by Jeff in Pa
tbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?
I will as soon as dimensions are verified :beer:

Jeff

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Jan 19, 2014 11:44 am
by Jeff in Pa
tbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?
Yes I do

~~~~~~~~~~~

Original style lift pin
Image

$22 plus shipping

~~~~~~~~~~~~~

QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)

These are 1/2 -13 LEFT HAND thread
Image

Image

I'll also sell just the bolt and castle nut too
Image

Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Feb 23, 2014 6:11 pm
by Jeff in Pa
Narrow Frame rear lift attachment bracket for lift handle.
Image

$22 plus shipping

~~~~~~
~~~~~~~~

Image

Wide Frame lift brackets also $22 plus shipping


~~~~~~~~~~~~~~~~~~~~~~~

Image

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Feb 23, 2014 6:34 pm
by edc
Jeff, Id like to buy to brass wear buttons

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sat Apr 26, 2014 1:58 pm
by Jeff in Pa
Just added PTO pulley pullers

Thanks
Jeff

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Apr 27, 2014 6:03 pm
by F Currier Northern Maine
Jeff, your PTO pulley puller is so close to what I've been trying to configure - and I can't make one for your price. I've PM'd you because my email isn't set up to just click on your address. I think you've got the answer to pulling one of them without damaging/bending it and I know what they cost new! Ouch, that hurt! :)

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Apr 27, 2014 8:53 pm
by l palma
Frank,
I have one of those and it works great!!
I even have the one one for the welded baskets.

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Tue Apr 29, 2014 9:01 am
by PTWannaHave
Hello Jeff,

Ever thought of designing/building a better PTO pulley? The stock version is flimsy/thin:

- makes it prone to distortion
- doesn't contribute to engine torque (but I assume it could with weight)
- is most likely not balanced
- without your removal tool, easily bent during removal
- does not seem to always allow enough space for the bolt head that holds the S/G bracket

Just some thoughts as I will be putting the stock PTO pulley back on a fresh rebuild in the near future...

Ciao,

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Mon May 05, 2014 8:55 pm
by F Currier Northern Maine
Thanks, Jeff !! The one on the right is as far as I'd got - and I don't weld! (Now I can go paint it)!

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Jun 01, 2014 11:08 am
by Jeff in Pa
Now available--90* gear box shafts


90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.

Image

$52 each or $97 for the pair shipped ( USA )

If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sat Jun 07, 2014 9:28 pm
by vince_o
Jeff you do such nice work!

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sun Aug 03, 2014 6:40 pm
by Jeff in Pa
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
Image

$22 plus shipping
( $15 with sleeve hitch adapter order )

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Wed Oct 01, 2014 7:18 pm
by Jeff in Pa
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Image

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Thu Nov 20, 2014 5:45 pm
by tinnerlee
I would like to buy a pto pulley puller how do I order one thanks

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Mon Nov 24, 2014 9:36 pm
by LFR
:email:

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Sat Feb 28, 2015 3:29 pm
by Jeff in Pa
Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox.

Image

$25 plus shipping

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Mon Apr 24, 2017 7:43 pm
by jturner008
Jeff; I am interested in the sleeve hitch are they still available contact me a Jturner008@centurylink.net Thanks Jim Turner

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Mon Aug 12, 2019 4:08 pm
by BearKiller
Jeff in Pa wrote: ~~~~~~~~~

Brass PTO button
Image
$8.50 each shipped

~~~~~~~
>>> EMERGENCY <<< !
Are these still available ?
As best I remember, I bought three from you (or somebody) a few years ago; the first one is getting thin and I have tore this place apart trying to find where I stashed the extras.
How do I order ?
Do you do PayPal ?

Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts

Posted: Mon Aug 12, 2019 5:26 pm
by Jeff in Pa
Best way to contact me is email.

I PM'd you and yes, I can accept paypal

Jeff