Page 1 of 1
1650 SGT
Posted: Tue Sep 27, 2011 8:09 pm
by cub1450
Well I got to thinking (I know bad idea to start thinking) I parted a 1000 because a bad clutch and one of my buddies wanted the rear end to do a cast iron conversion so I sold the rear,motor,and gauges well I wanted a super but couldn`t afford one so I thought why don`t I build one and thats how it started.......
Doesn`t look bad mocked up
Re: 1650 SGT
Posted: Tue Sep 27, 2011 8:18 pm
by cub1450
Bigger Tires and wheels and I got the cross member cut out.
Re: 1650 SGT
Posted: Tue Sep 27, 2011 8:20 pm
by cub1450
Picked up a great running 16 horse Kohler
Here is a vid
http://www.youtube.com/watch?v=FVxVblRepzI
Re: 1650 SGT
Posted: Tue Sep 27, 2011 8:35 pm
by cub1450
Got the frame extensions made and mocked up.
Re: 1650 SGT
Posted: Tue Sep 27, 2011 8:43 pm
by cub1450
Got the frame extensions welded on and some black paint on them to keep the rust away.
Re: 1650 SGT
Posted: Tue Oct 04, 2011 3:42 pm
by Dave C
Jed,
Looks good what r u doing for a transmission? them super trannys are mightly expensive!
dave
Re: 1650 SGT
Posted: Tue Oct 04, 2011 8:59 pm
by cub1450
I`m using a cast rear with a super pump.
Re: 1650 SGT
Posted: Wed Oct 05, 2011 5:42 am
by mgonitzke
Did you change the reduction gear in the CI rear to one from a super?
Re: 1650 SGT
Posted: Wed Oct 05, 2011 8:07 pm
by cub1450
Sure did.
Re: 1650 SGT
Posted: Sat Feb 18, 2012 8:42 pm
by cub1450
I am finally posting an update.
Well I got a rear end,all the hydraulics ,a dash tower off a 1650 ,lights,and a great looking gas tank and firewall .
Got the dash bolted down and the hydraulics and wiring hooked up this evening.
Hope two get the rear in sometime this week.
Re: 1650 SGT
Posted: Sat Feb 18, 2012 8:50 pm
by cub1450
Re: 1650 SGT
Posted: Tue Feb 21, 2012 11:19 pm
by cub1450
Shes a roller!!!!!!!!!!!!!
Got the rear end in and started adding on to the linkage today.
Hope to get the linkage and hydro lines done tomorrow.
Re: 1650 SGT
Posted: Tue Feb 21, 2012 11:23 pm
by cub1450
Re: 1650 SGT
Posted: Tue Feb 21, 2012 11:26 pm
by cub1450
Re: 1650 SGT
Posted: Tue Feb 21, 2012 11:29 pm
by cub1450
Re: 1650 SGT
Posted: Wed Feb 22, 2012 11:53 pm
by cub1450
Got a peice of 1x1 in. square tubing to rasise the fender pan and already welded nuts on the inside for the fender pan to bolt to.
Re: 1650 SGT
Posted: Wed Feb 22, 2012 11:55 pm
by cub1450
Heres an update on this thread.
Got the Super in the big garage.
Started working on the Cat 0 3pt hitch.I got the spots marked where I was going to put the new collars ,but the 1 in. hole saw gave out so i`ll have to get a new one.
So I started working on getting the fenders mounted.
Got the square tubing welded to the frame and started welding the foot supports on.
Re: 1650 SGT
Posted: Wed Feb 22, 2012 11:56 pm
by cub1450
Finished welding on the foot rest supports and drove it around for a bit then I stuck the BIGGER tires on and wow!! does it feel different sitting in the seat .Now to build the Cat 0 and save up for new tires ,wheels and a super front axle assembly.
I think its going to look mean with fire stone 26x12x12s and V61s .
Re: 1650 SGT
Posted: Wed Sep 05, 2012 9:16 pm
by cub1450
Re: 1650 SGT
Posted: Wed Sep 05, 2012 9:18 pm
by cub1450
Re: 1650 SGT
Posted: Wed Sep 05, 2012 9:23 pm
by cub1450
Re: 1650 SGT
Posted: Wed Sep 05, 2012 9:26 pm
by cub1450
Re: 1650 SGT
Posted: Wed Sep 05, 2012 9:28 pm
by cub1450
Re: 1650 SGT
Posted: Wed Sep 05, 2012 9:28 pm
by cub1450
Pulled the front wheels today packed the bearings,and gave it a bath .Took a spare rear cover in shop class and going to get the top link mount cut out of some 1/4 in. steel.Should be ready to roll in a little while.
Re: 1650 SGT
Posted: Sun Sep 16, 2012 10:47 am
by cub1782
Looks good jed