122 help
-
- Posts: 14
- Joined: Sun Nov 07, 2010 8:45 pm
- First and Last Name: Mike Stoneroad
- Location: Blackshear, Georgia
122 help
I just recently moved to a new town, & initially bring any Cubs with me. On Labor Day, I went back to my other house near Atlanta & brought back a 122 that I've had for nearly 20 years. It has a creeper gear, hyd. lift, rear lift, Brinly adapter, rear ag tires, headlights & a tail light. I used to use it to plow my garden. I took the pto clutch off years ago & didn't remember if I was missing any parts. My only problem now is that I'm missing the key stock & the set screws for the pto cage/starter pulley. Could anyone out there let me know what size the key stock & what size set screws I need to put it back together? I will try to get some pictures posted within the next few days. Thanks in advance.
-
- Posts: 190
- Joined: Wed Sep 08, 2010 9:20 am
- First and Last Name: Paul E. Funk
- Location: Boonville, Indiana
Re: 122 help
Mike, according to the TC-113 manual, the key is 1/4 X 7/8. It doesn't list the size of the set screws. Hopefully someone else will know that.
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 122 help
Here you go Mike. These are to be used for anchoring the pulley to the bearing.
The set screws that mount above are retainers and they can be 3/8" or 1/4" long but I think they were 1/4 from the factory-
- Posts: 14
- Joined: Sun Nov 07, 2010 8:45 pm
- First and Last Name: Mike Stoneroad
- Location: Blackshear, Georgia
Re: 122 help
Thanks for the info. Now I'll get to putting it all back together.
-
- Posts: 168
- Joined: Sun Oct 10, 2010 9:04 am
- First and Last Name: Dale Campbell
- Location: Summerville, PA
Re: 122 help
the set screws for the basket pulley are 5/16" course. thread I think 1/2" long
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 122 help
From the TC-113 parts manual-
Section E (122) Pg. 20
Rear frame and driving mechanisms
Item 10
IH-59983-C1 Pulley, Mower Actuating............1
IH-23025-R1 Screw, 1/4-20 X 1/2 Hex Soc.......3
Hd Cone Pt Set
IH-23026-R1 Screw, 1/4 20 X 1/4 Hex Soc.......3
Hd F Pt Set
Section E (122) Pg. 20
Rear frame and driving mechanisms
Item 10
IH-59983-C1 Pulley, Mower Actuating............1
IH-23025-R1 Screw, 1/4-20 X 1/2 Hex Soc.......3
Hd Cone Pt Set
IH-23026-R1 Screw, 1/4 20 X 1/4 Hex Soc.......3
Hd F Pt Set
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 122 help
Paul and Dale are both correct about the pulley set screws.
The key is listed as IH-452779 R1 Key, 1/4 x 7/8 Square Parallel .....1
The screw is listed as KH-X-60-50 Screw, Flywheel Pulley Set..........1
No size for it is recorded in the parts manual.
The thread for that screw should be 5/16-18.
So yes, Dale is right about the approximate length and size.
Sorry about the confusion guys, I was trying to provide info for the screws for the PTO pulley
The key is listed as IH-452779 R1 Key, 1/4 x 7/8 Square Parallel .....1
The screw is listed as KH-X-60-50 Screw, Flywheel Pulley Set..........1
No size for it is recorded in the parts manual.
The thread for that screw should be 5/16-18.
So yes, Dale is right about the approximate length and size.
Sorry about the confusion guys, I was trying to provide info for the screws for the PTO pulley