54" Blade on 2082
-
- Posts: 258
- Joined: Mon Sep 06, 2010 6:38 am
- First and Last Name: Ken Brothers
- Location: Ebensburg, PA
54" Blade on 2082
Downloaded amodel 761-406 Haban manual Thanks for the info on that. Got everything together and its mounted ; except for where it mounts to frame at rear. My subframe sweeps up at rear and both sides have a piece that goes up oneach side of the frame anchor plates (used for the mower deck ) The mounting pin will not fit thru the outside holes on the sub frame, they are smaller than the two on the insde Not being the sharpest crayon in the box what am I missig here? Thanks Ken in Pa
-
- Posts: 24
- Joined: Sun Dec 26, 2010 9:19 pm
- First and Last Name: Richard Boley
- Location: Brownsburg, IN 46112
Re: 54" Blade on 2082
I've got exactly the same blade on my 1872. My pin fits both as would be expected, so has anyone "customized" your frame? I guess I would just drill out the frame to the same hole size. I wouldn't put a smaller rod in and allow some slop.
-
- Posts: 258
- Joined: Mon Sep 06, 2010 6:38 am
- First and Last Name: Ken Brothers
- Location: Ebensburg, PA
Re: 54" Blade on 2082
thanks richard Ken in Pa
- Racenitro
- Posts: 354
- Joined: Tue Sep 07, 2010 10:31 pm
- First and Last Name: Frank S. Morski
- Location: O'Fallon, Il
Re: 54" Blade on 2082
The 54" blade has two plates that bolt to the frame and the sub frame for the blade mounts to these plates. They are about 5" x 6" ..
I have two but the are at the farm 50 miles away or I'd shoot you a pcture.
Your subframe should have a slot on the end so the plate slips between the two sides and a pin goes though both sides...
I looked through my literature but I don' t have the manual for the blade... everything else...
I have two but the are at the farm 50 miles away or I'd shoot you a pcture.
Your subframe should have a slot on the end so the plate slips between the two sides and a pin goes though both sides...
I looked through my literature but I don' t have the manual for the blade... everything else...
-
- Posts: 258
- Joined: Mon Sep 06, 2010 6:38 am
- First and Last Name: Ken Brothers
- Location: Ebensburg, PA
Re: 54" Blade on 2082
Frank, I think that's what is going on there are two different plates One ha-14300 which is the one on this tractor which had a 60" deck hung from them. The anchor plates for the plow are CC-20277 and NLA Always my luck. Thanks Ken in Pa
- Racenitro
- Posts: 354
- Joined: Tue Sep 07, 2010 10:31 pm
- First and Last Name: Frank S. Morski
- Location: O'Fallon, Il
Re: 54" Blade on 2082
Sounds like I should make a few from my set....
-
- Posts: 258
- Joined: Mon Sep 06, 2010 6:38 am
- First and Last Name: Ken Brothers
- Location: Ebensburg, PA
Re: 54" Blade on 2082
Does anyone have a pic of how the lift tube connects to the rockshaft?" Mine seems to be too long Thanks Ken in Pa Seems I,m missing part# 719-3093 Goes on end of rockshaft and is aqn adapter for this Haban front plow on hi serial# 2082 Again thanks Dimensions to make would also help
-
- Posts: 258
- Joined: Mon Sep 06, 2010 6:38 am
- First and Last Name: Ken Brothers
- Location: Ebensburg, PA
Re: 54" Blade on 2082
Local Cub dealer says he can order part # 719-3093 It will be in Wed or Thur It is the snow blade adapterfor a 2082 higher ser # Kinda pricey Tho $75 ouch Ken in Pa Just got back from dealer they couldn't order: but found a used one $40 Going out to put it on and finish mounting blower to 1250