Parts by Jeff-sleeve hitch, PTO buttons and custom parts
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Parts by Jeff-sleeve hitch, PTO buttons and custom parts
I make a large variety of parts for cub cadets. I can make custom parts too. All parts are made by myself, I'm a machinist / fabricator with over thirty years experience.
Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps
$120 shipped
$135 shipped with one set of drilled and one set of slotted straps
Add a lift pin for an additional $10
add a triple drilled lift pin for an additional $15
Extended length to clear tiller mount add $5
I can make these custom length if needed.
~~~~~~~
double hole rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
$17 plus shipping
( $10 with sleeve hitch adapter order )
~~~~~~~~~
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
$22 plus shipping
( $15 with sleeve hitch adapter order )
~~~~~~~~~~~~~~~~~~
Height adjuster knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.
$23 shipped
~~~~~~~~~~~
1/2-13NC threaded rod for use with above knob ( or factory knob )
$9 shipped
~~~~~~~~~
Brass PTO button
$8.50 each shipped
~~~~~~~
Pair of "frankenstein" bolt and nuts for WF rear lifts
$32 shipped
~~~~~~~~~
Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.
$17 shipped
~~~~~~~~~~~
Wide frame solid motor mounts with washers, Grade 8 flanged bolts and nylock nuts.
$43 shipped for set of four.
~~~~~~~~~~~
Headlight rings for 1X2/1X3/1X4/1X5
$32 per pair plus shipping
~~~~~~~~~~~
Original style lift pin
$22 plus shipping
~~~~~~~~~~~~~
QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)
These are 1/2 -13 LEFT HAND thread
I'll also sell just the bolt and castle nut too
Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping
~~~~~~~~~~~
Narrow Frame rear lift attachment bracket for lift handle. ( wide frame brackets available too )
$22 plus shipping
~~~~~~~~
Wide Frame lift brackets also $22 plus shipping
~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PTO pulley puller
The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier.
Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.
It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)
$22 each plus shipping
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.
$52 each or $97 for the pair shipped ( USA )
If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox or to manual transmission.
$25 plus shipping
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If you order more than one item, I will do my best to keep shipping costs as low as possible.
All parts manufactured by me and mailed from the Palm,PA post office
Please either PM or email me
Thanks
Jeff
Heavy duty sleeve hitch adapter with two drilled lifting straps or two slotted lifting straps
$120 shipped
$135 shipped with one set of drilled and one set of slotted straps
Add a lift pin for an additional $10
add a triple drilled lift pin for an additional $15
Extended length to clear tiller mount add $5
I can make these custom length if needed.
~~~~~~~
double hole rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
$17 plus shipping
( $10 with sleeve hitch adapter order )
~~~~~~~~~
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
$22 plus shipping
( $15 with sleeve hitch adapter order )
~~~~~~~~~~~~~~~~~~
Height adjuster knob for 1/1A/2A tillers using 1/2-13 threaded rod. Has correct milled radius on bottom to match rear lift pin.
$23 shipped
~~~~~~~~~~~
1/2-13NC threaded rod for use with above knob ( or factory knob )
$9 shipped
~~~~~~~~~
Brass PTO button
$8.50 each shipped
~~~~~~~
Pair of "frankenstein" bolt and nuts for WF rear lifts
$32 shipped
~~~~~~~~~
Pair of straps for the front of the QA mounts. No more fumbling with bolts,nuts and washers. Slide these in the hole and secure with a 1/2-13NC in the factory welded nut inside the frame.
$17 shipped
~~~~~~~~~~~
Wide frame solid motor mounts with washers, Grade 8 flanged bolts and nylock nuts.
$43 shipped for set of four.
~~~~~~~~~~~
Headlight rings for 1X2/1X3/1X4/1X5
$32 per pair plus shipping
~~~~~~~~~~~
Original style lift pin
$22 plus shipping
~~~~~~~~~~~~~
QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)
These are 1/2 -13 LEFT HAND thread
I'll also sell just the bolt and castle nut too
Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping
~~~~~~~~~~~
Narrow Frame rear lift attachment bracket for lift handle. ( wide frame brackets available too )
$22 plus shipping
~~~~~~~~
Wide Frame lift brackets also $22 plus shipping
~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
PTO pulley puller
The pulley puller uses the 5/16" threaded holes in the pulley to pull it off much easier.
Each unit is supplied with handle and threaded rod with centering point to locate on the crankshaft. Use a 9/16" wrench or socket.
It's used as shown here ( version shown in pictures does not have the weld cutouts, all pullers have that now)
$22 each plus shipping
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.
$52 each or $97 for the pair shipped ( USA )
If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox or to manual transmission.
$25 plus shipping
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If you order more than one item, I will do my best to keep shipping costs as low as possible.
All parts manufactured by me and mailed from the Palm,PA post office
Please either PM or email me
Thanks
Jeff
Last edited by Jeff in Pa on Sun Mar 01, 2015 10:01 am, edited 11 times in total.
125 & 125 with hydraulic lift
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Just added headlight rings
125 & 125 with hydraulic lift
-
- Posts: 101
- Joined: Fri Jan 03, 2014 7:29 pm
- First and Last Name: Terry Davis
- Location: Greenfield, IN
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Jeff - do you by chance make lift pins for the Originals?
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
I will as soon as dimensions are verifiedtbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?
Jeff
125 & 125 with hydraulic lift
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Yes I dotbdavis123 wrote:Jeff - do you by chance make lift pins for the Originals?
~~~~~~~~~~~
Original style lift pin
$22 plus shipping
~~~~~~~~~~~~~
QA36 / QA 42 / QA36A / QA42A belt tensioner bolt, castle nut & plate button . This style has a welded nut in the end for use with 3/4" wrench. ( original style will offered later after I bend up handles)
These are 1/2 -13 LEFT HAND thread
I'll also sell just the bolt and castle nut too
Complete unit as shown $30 plus shipping
Adjustment bolt with castle nut $17 plus shipping
Plate button $17 plus shipping
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:38 pm, edited 1 time in total.
125 & 125 with hydraulic lift
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Narrow Frame rear lift attachment bracket for lift handle.
$22 plus shipping
~~~~~~
~~~~~~~~
Wide Frame lift brackets also $22 plus shipping
~~~~~~~~~~~~~~~~~~~~~~~
$22 plus shipping
~~~~~~
~~~~~~~~
Wide Frame lift brackets also $22 plus shipping
~~~~~~~~~~~~~~~~~~~~~~~
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:39 pm, edited 1 time in total.
125 & 125 with hydraulic lift
-
- Posts: 1
- Joined: Sun Oct 21, 2012 8:52 pm
- First and Last Name: Ed Colan
- Location: grand island, NY
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Jeff, Id like to buy to brass wear buttons
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Just added PTO pulley pullers
Thanks
Jeff
Thanks
Jeff
125 & 125 with hydraulic lift
-
- Posts: 42
- Joined: Fri Sep 24, 2010 11:19 am
- First and Last Name: Frank A. Currier
- Location: Portage Lake, Maine
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Jeff, your PTO pulley puller is so close to what I've been trying to configure - and I can't make one for your price. I've PM'd you because my email isn't set up to just click on your address. I think you've got the answer to pulling one of them without damaging/bending it and I know what they cost new! Ouch, that hurt!
- l palma
- Posts: 738
- Joined: Mon Sep 06, 2010 9:46 am
- First and Last Name: Lew Palma
- Location: Montague, N.J.
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Frank,
I have one of those and it works great!!
I even have the one one for the welded baskets.
I have one of those and it works great!!
I even have the one one for the welded baskets.
- Attachments
-
- 20140410_101034.jpg (810.63 KiB) Viewed 13545 times
-
- Posts: 295
- Joined: Wed Apr 11, 2012 12:39 pm
- First and Last Name: Ben Michaud
- Location: Richmond, Ontario
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Hello Jeff,
Ever thought of designing/building a better PTO pulley? The stock version is flimsy/thin:
- makes it prone to distortion
- doesn't contribute to engine torque (but I assume it could with weight)
- is most likely not balanced
- without your removal tool, easily bent during removal
- does not seem to always allow enough space for the bolt head that holds the S/G bracket
Just some thoughts as I will be putting the stock PTO pulley back on a fresh rebuild in the near future...
Ciao,
Ever thought of designing/building a better PTO pulley? The stock version is flimsy/thin:
- makes it prone to distortion
- doesn't contribute to engine torque (but I assume it could with weight)
- is most likely not balanced
- without your removal tool, easily bent during removal
- does not seem to always allow enough space for the bolt head that holds the S/G bracket
Just some thoughts as I will be putting the stock PTO pulley back on a fresh rebuild in the near future...
Ciao,
PTWannaHave
-
- Posts: 42
- Joined: Fri Sep 24, 2010 11:19 am
- First and Last Name: Frank A. Currier
- Location: Portage Lake, Maine
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Thanks, Jeff !! The one on the right is as far as I'd got - and I don't weld! (Now I can go paint it)!
- Attachments
-
- Jeff Derstine Puller 001.JPG (491.69 KiB) Viewed 13491 times
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Now available--90* gear box shafts
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.
$52 each or $97 for the pair shipped ( USA )
If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )
90* gear box shafts for tillers and snow throwers. Made from 3/4" diameter 4140 P alloy steel ( turned ,ground and polished ) with on size keyways and snap ring grooves cut.
$52 each or $97 for the pair shipped ( USA )
If you have a "BB" angle drive gear box, I can make those shafts if you send me the shaft to copy ( it will be returned if wanted )
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:39 pm, edited 1 time in total.
125 & 125 with hydraulic lift
- vince_o
- Moderator
- Posts: 2045
- Joined: Mon Sep 06, 2010 3:20 am
- First and Last Name: Vince Ochiuto
- Location: Pickens, SC
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Jeff you do such nice work!
"It's a damn poor mind that can only think of one way to spell a word."
-Andrew Jackson
-Andrew Jackson
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Triple drilled rear lift pin for rear lift casting. I drill these so they can be positioned with the holes vertical or horizontal. They are secured with a 3/16" cotter pin and also have a cotter pin where it goes thru the casting.
$22 plus shipping
( $15 with sleeve hitch adapter order )
$22 plus shipping
( $15 with sleeve hitch adapter order )
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:40 pm, edited 1 time in total.
125 & 125 with hydraulic lift
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Transfer shaft for the QA snow throwers. $37 shipped or $32 with either ( or both ) of the 90* gear box shafts
Last edited by Jeff in Pa on Fri Jan 02, 2015 7:40 pm, edited 1 time in total.
125 & 125 with hydraulic lift
-
- Posts: 1
- Joined: Wed Nov 19, 2014 9:12 pm
- First and Last Name: mike beadle
- Location: oskaloosa, IA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
I would like to buy a pto pulley puller how do I order one thanks
-
- Posts: 351
- Joined: Fri Jan 17, 2014 4:28 pm
- First and Last Name: Lorin Burch
- Location: Boyne City, MI
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
67 Case 155, 66 Colt 2310, 68 John Deere 110w/ haban sickle bar mower, 59 simplicity 700 wonderboy, 62 allis Chalmers b1, Fairbanksmorse 3 wheel, 1944 McCormick peering O4, H, 1948 Farmall Cub, C.
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Now offering driveshaft couplers for 5/8" driveshaft to creeper gearbox.
$25 plus shipping
$25 plus shipping
125 & 125 with hydraulic lift
-
- Posts: 2
- Joined: Wed Apr 12, 2017 4:23 pm
- First and Last Name: Jim Turner
- Location: Sheldon Mo
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Jeff; I am interested in the sleeve hitch are they still available contact me a Jturner008@centurylink.net Thanks Jim Turner
-
- Posts: 180
- Joined: Wed Nov 07, 2012 12:27 am
- First and Last Name: George Riley
- Location: Poverty Springs KY 2018 Wettest State in the Nation
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
>>> EMERGENCY <<< !Jeff in Pa wrote: ~~~~~~~~~
Brass PTO button
$8.50 each shipped
~~~~~~~
Are these still available ?
As best I remember, I bought three from you (or somebody) a few years ago; the first one is getting thin and I have tore this place apart trying to find where I stashed the extras.
How do I order ?
Do you do PayPal ?
- Jeff in Pa
- Posts: 665
- Joined: Sun Sep 12, 2010 8:06 am
- First and Last Name: Jeff Derstine
- Location: Zionsville,PA
Re: Parts by Jeff-sleeve hitch, PTO buttons and custom parts
Best way to contact me is email.
I PM'd you and yes, I can accept paypal
Jeff
I PM'd you and yes, I can accept paypal
Jeff
125 & 125 with hydraulic lift