102 light installation
- Farmallgray
- Posts: 1021
- Joined: Mon Sep 06, 2010 7:39 am
- First and Last Name: Todd Markle
- Location: Spring Mills, Pa
102 light installation
Do we have the instructions for installing the lighting kit on a 1x2/3? I can't seem to find it in the documents section. I just want to make sure I have all the correct hardware and such.
See my IH, Cub Cadet and tractor pulling youtube videos;
http://www.youtube.com/user/farmallgray
http://www.youtube.com/user/farmallgray
- Paul B
- Posts: 586
- Joined: Wed Sep 08, 2010 8:20 pm
- First and Last Name: Paul R. Bell
- Location: Louisville, KY, where all your IH built Cub Cadets were born
Re: 102 light installation
Todd, Although it doesn't tell you how to install lights, the 102/122/123 Parts Manual shows/tells everything needed for the light installation, however there is not one on this site.
May you always have as many landings as you do takeoff's.........
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 102 light installation
Todd, does this help at all ?
From TC-113 section D (102)
Click on image to enlarge.
From TC-113 section D (102)
Click on image to enlarge.
-
- Posts: 101
- Joined: Mon May 02, 2011 2:41 pm
- First and Last Name: Doug Anderson
- Location: Peninsula, OH
Re: 102 light installation
There's a 70/100 install manual on another cub site. That's the only one I've even seen
- Farmallgray
- Posts: 1021
- Joined: Mon Sep 06, 2010 7:39 am
- First and Last Name: Todd Markle
- Location: Spring Mills, Pa
Re: 102 light installation
The rear light bracket has 2 holes that line up with the holes in the fender. One hole is 1/4" the other is 1/2". Both holes in the fender are 1/4". I was wondering if they used a flat washer on the bigger hole. Or did the bracket for the 1X2/3 have two 1/4" holes? I have the bracket from a 100. The parts list doesn't show a washer.
See my IH, Cub Cadet and tractor pulling youtube videos;
http://www.youtube.com/user/farmallgray
http://www.youtube.com/user/farmallgray
-
- Posts: 101
- Joined: Mon May 02, 2011 2:41 pm
- First and Last Name: Doug Anderson
- Location: Peninsula, OH
Re: 102 light installation
I don't have a tail light on mine but the fender has 2x 1/4" holes also.
Last edited by mortten on Mon Jul 20, 2015 7:12 pm, edited 1 time in total.
- l palma
- Posts: 738
- Joined: Mon Sep 06, 2010 9:46 am
- First and Last Name: Lew Palma
- Location: Montague, N.J.
Re: 102 light installation
Todd,
Here is how the one I have is mounted on a 123.
Hope this helps
Here is how the one I have is mounted on a 123.
Hope this helps
- Attachments
-
- DSC00749.JPG (306.82 KiB) Viewed 7664 times
- Farmallgray
- Posts: 1021
- Joined: Mon Sep 06, 2010 7:39 am
- First and Last Name: Todd Markle
- Location: Spring Mills, Pa
Re: 102 light installation
Apparently they must have chaged the hole size in the bracket from the 70/100 to the 1X2/3 series. Kind of sucks because I made the bracket new using the one from my 100 as a pattern. If I had looked at the 102 fender I could have drilled the hole in the smaller size. Oh well, stuff happens. I'll just put a flat washer on it for now.
See my IH, Cub Cadet and tractor pulling youtube videos;
http://www.youtube.com/user/farmallgray
http://www.youtube.com/user/farmallgray
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 102 light installation
I went out and took a look at my 102. It does have the two 1/4" holes already there. I can provide dimensions should you need them. It also has the single Speaker 143 tail light. I have seen this style of light mount on many Cubs of this series. My assumption has been up to this point that's how the factory install looked. Disregard the 1x4,5 style seat mount, that is something I added to raise the rubber seat, everything ever said negative about the rubber style seat is cured by adding a riser mount sofar as I'm concerned- it feels great setup that way
- Farmallgray
- Posts: 1021
- Joined: Mon Sep 06, 2010 7:39 am
- First and Last Name: Todd Markle
- Location: Spring Mills, Pa
Re: 102 light installation
Ken,
I already had the holes in the fender (I assume they were there from factory since both fenders have them).
I had always assumed that that style light came with the 1X4 series.
I already had the holes in the fender (I assume they were there from factory since both fenders have them).
I had always assumed that that style light came with the 1X4 series.
See my IH, Cub Cadet and tractor pulling youtube videos;
http://www.youtube.com/user/farmallgray
http://www.youtube.com/user/farmallgray
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 102 light installation
Todd-
I'm not a die hard purist by any means and leave that to those who are more versed in the matter than I but that sure seems to raise one heck of a darn interesting question.
Was there a point in the 1x2,3 series that the Grote light was changed over to the Speaker light ? I don't recall the SN on mine but do remember that it was somewhere along the line of nearing what would be considered a higher number for that series. 172xxx comes to mind for whatever reason. It's the middle of the night, I just got out of work, and I ain't lookin
Really though there's no telling what folks do to these over the course of nearly fifty years.
I'm not a die hard purist by any means and leave that to those who are more versed in the matter than I but that sure seems to raise one heck of a darn interesting question.
Was there a point in the 1x2,3 series that the Grote light was changed over to the Speaker light ? I don't recall the SN on mine but do remember that it was somewhere along the line of nearing what would be considered a higher number for that series. 172xxx comes to mind for whatever reason. It's the middle of the night, I just got out of work, and I ain't lookin
Really though there's no telling what folks do to these over the course of nearly fifty years.
- Farmallgray
- Posts: 1021
- Joined: Mon Sep 06, 2010 7:39 am
- First and Last Name: Todd Markle
- Location: Spring Mills, Pa
Re: 102 light installation
If someone had a parts catalog from just after the 1X4/5 came out, that may tell the story since the rear panel would have been changed to one with the screw inserts for the oval light.
See my IH, Cub Cadet and tractor pulling youtube videos;
http://www.youtube.com/user/farmallgray
http://www.youtube.com/user/farmallgray
-
- Posts: 1364
- Joined: Mon Sep 06, 2010 2:25 pm
- First and Last Name: Kenneth LaPatta
- Location: Rockingham VT.
Re: 102 light installation
That could well be but just try finding one. My TC-113 Manual (REV 26- May 30, 1991) is pretty cut and dry about it. Machines up to and including the 123, Grote light. 1X4,5 series and up, Speaker light.
Lew's image has got to be the one. That thing on mine, I'll guess I'll never know, he was a stripped down mutt the day I laid eyes on him but it goes like Hell and that's what matters to me
Lew's image has got to be the one. That thing on mine, I'll guess I'll never know, he was a stripped down mutt the day I laid eyes on him but it goes like Hell and that's what matters to me