Steel plug over pinion nut - WF hydrostat transaxle

This is your place for high horsepower and traction!
Post Reply
DaveKamp
Posts: 557
Joined: Mon Sep 06, 2010 10:19 am
First and Last Name: Dave Kamp
Location: LeClaire, Ia

Steel plug over pinion nut - WF hydrostat transaxle

Post by DaveKamp »

Hey guys-

the WF iron hydrostat axle has what appears to be a steel cap or plug pressed into the transaxle housing to seal off access to the pinion nut.

Is there a clever way to remove this... to gain access to removing the pinion... without damaging it?
Yes, I'm a Mad Scientist... but I'm usually happy, even when things ain't goin right.
User avatar
Tom Scott
Chief Moderator
Posts: 1836
Joined: Mon Sep 06, 2010 9:11 pm
First and Last Name: Tom Scott
Location: Bentley Springs, Maryland

Re: Steel plug over pinion nut - WF hydrostat transaxle

Post by Tom Scott »

Dave - I assume it is same as with the newer aluminum rears, just an expendable disc type domed freeze plug. While rear is disassembled, easy to knock out, replace with new.

Cub likely still lists a replacement plug to eliminate guesswork for proper replacement part. Put some sealant around the edges and then hit squarely in the center with very large drift to expand.
1872, 46", 50C decks, Haban dozer blade, 450 snow blower
2182-1, Kwik-Way Loader, 3-pt & rear pto, 442 tiller
2182-2, 54" deck, 551 snow blower
Past tractors:  1541, 2135
<><
DaveKamp
Posts: 557
Joined: Mon Sep 06, 2010 10:19 am
First and Last Name: Dave Kamp
Location: LeClaire, Ia

Re: Steel plug over pinion nut - WF hydrostat transaxle

Post by DaveKamp »

Okay, thanks Tom. I didn't see a good angle to get at it to knock it loose, other than try to knock one side inward enough to get the opposite to pop out into vise-grip range. Izzat the standard modus operandi?
Yes, I'm a Mad Scientist... but I'm usually happy, even when things ain't goin right.
User avatar
Tom Scott
Chief Moderator
Posts: 1836
Joined: Mon Sep 06, 2010 9:11 pm
First and Last Name: Tom Scott
Location: Bentley Springs, Maryland

Re: Steel plug over pinion nut - WF hydrostat transaxle

Post by Tom Scott »

Dave - Been so long, I can't remember what I did. I think I drilled most of the way through then used a sharp punch to beat a hole the rest of the way through,then pried it out. Do not try to beat one edge in, the lip behind it will prevent that.

Here is my thread that has the rear set-up, but I didn't show plug removal: viewtopic.php?f=8&t=5282&hilit=cinderella&start=90
1872, 46", 50C decks, Haban dozer blade, 450 snow blower
2182-1, Kwik-Way Loader, 3-pt & rear pto, 442 tiller
2182-2, 54" deck, 551 snow blower
Past tractors:  1541, 2135
<><
DaveKamp
Posts: 557
Joined: Mon Sep 06, 2010 10:19 am
First and Last Name: Dave Kamp
Location: LeClaire, Ia

Re: Steel plug over pinion nut - WF hydrostat transaxle

Post by DaveKamp »

Thanks Tom!!!
Yes, I'm a Mad Scientist... but I'm usually happy, even when things ain't goin right.
User avatar
Dave C
Web Developer
Posts: 1026
Joined: Mon Sep 06, 2010 7:12 am
First and Last Name: David Chester
Location: Wallingford, CT

Re: Steel plug over pinion nut - WF hydrostat transaxle

Post by Dave C »

part to replace that plug is a Dorman 550-030
prob can cross it to another manufacturer

i keep a good stockpile of them handy
Trying to save cubs... one at a time.......
DaveKamp
Posts: 557
Joined: Mon Sep 06, 2010 10:19 am
First and Last Name: Dave Kamp
Location: LeClaire, Ia

Re: Steel plug over pinion nut - WF hydrostat transaxle

Post by DaveKamp »

Dave C wrote: Tue Jun 30, 2020 7:10 am part to replace that plug is a Dorman 550-030
prob can cross it to another manufacturer

i keep a good stockpile of them handy
Thanks for the tip, Dave!

Sorry about the slow progress, Gents - Other than a start to a pair of 8-bolt rear wheels, I have made NO progress on Mutt's Mustang LSD rear end in the last six months... still slow recovery on the knee blowout, and lots of honey-do tasks atop the priority pile, but I'm making the workshop more-ready slow-but-steady. Once I get a few more things straightened out in the shop, I'll get back to it, get those wheels done, axle outers fab'd, and start reassembly of the rearend with the beefy new LSD.
Yes, I'm a Mad Scientist... but I'm usually happy, even when things ain't goin right.
Post Reply